User manual NAVMAN W300

[. . . ] We recommend rinsing the W300 with fresh water after any exposure to salt water. CAUTION: Please ensure battery cover is in place during cleaning. Store the W300 away from direct sunlight or extreme heat sources. (Remove battery before storing for an extended period. ) 1. 3 Water resistance The Navman W300 GPS Sport. Tool is water resistant. 1-6 W300 NAVMAN W300 ­ General information 1. 4 Changing the battery Always shut down the W300 before changing the battery. Note: All system settings, and the calculated data that was stored at the last controlled shutdown*, are retained when the battery is removed. [. . . ] To set weight units 1) Press to start editing (weight units flash). 4) Press to go to the next option, or hold to leave setup. W300 1-13 W300 ­ Setup NAVMAN 4. 1. 5 Edit user weight Edit the user weight value (used for calculating calories burned). user weight kg SYSTEM SET Access this option If necessary, press and hold to turn the power on and enter setup. Press repeatedly until the screen appears as shown above. To edit user weight to start editing (weight value flashes). 1) Press 2) Press repeatedly to increase value by 1 (hold to increase values quickly), or press repeatedly to decrease value by 1 (hold to decrease values quickly). 3) Press 4) Press to go to the next option, or hold to leave setup. 4. 1. 6 Set energy units Set energy units (kcal or kJ) for displaying energy (calories) burned when using Cal mode (see Section 5. 1. 4). kcal SYSTEM SET energy units Access this option If necessary, press and hold to turn the power on and enter setup. Press repeatedly until the screen appears as shown above. To set energy units 1) Press to start editing (energy units flash). 4) Press to go to the next option, or hold to leave setup. 1-14 W300 NAVMAN W300 ­ Setup 4. 1. 7 Set speed units Set units for speed (km/h or mph). km km/h SYSTEM SET speed units Access this option If necessary, press and hold to turn the power on and enter setup. Press repeatedly until the screen appears as shown above. To set speed units to start editing (speed units flash). 1) Press 2) Press or to select km/h or mph. 3) Press 4) Press to go to the next option, or hold to leave setup. Note: Distance is displayed in units that correspond to the selected speed units. For example, if you select speed units `km/h', then distance is displayed in `km'. W300 1-15 W300 ­ Setup NAVMAN 4. 1. 8 Set offset (set local time) This option lets you adjust the W300 to display local time*. You only need to do this once, unless operating the unit in a new time zone. (* By default the W300 displays GPS time. current speed pace session distance PACE km km/h To access this mode If necessary, press to turn the power on and start normal operation. Press repeatedly until the screen appears as shown above. While in Speed mode to clear all* session data. (*Does not clear · Press and hold odometer. ) · Press to go to the next mode. 5. 1. 2 Speed (Average) mode This mode lets you monitor session distance, average speed and pace. average speed pace session distance PACE km km/h AVG To access this mode If necessary, press to turn the power on and start normal operation. Press repeatedly until the screen appears as shown above. While in Speed (Average) mode · Press and hold to clear all* session data. (*Does not clear odometer. ) · Press to go to the next mode. W300 1-19 W300 ­ Normal operation NAVMAN 5. 1. 3 Odometer mode This mode lets you monitor total distance. total distance km 2 873 Access this mode If necessary, press to turn the power on and start normal operation. [. . . ] Each of these disclaimers is in addition to, and does not reduce the effect of, any other disclaimer. No dealer has the authority to change this warranty. No event that voids any warranty of the Product will have any effect on these disclaimers or limitations of liability. This disclaimer will be construed under the laws of New Zealand without regard for any conflict of law rules. [. . . ]