User manual NAVMAN X300

[. . . ] NAVMAN English Deutsch Francaise Italiano Espana Português 1-3 2-1 3-1 4-1 5-1 6-1 X300 1-1 NAVMAN 1-2 X300 NAVMAN X300 ­ English X300 USER GUIDE English X300 1-3 Welcome NAVMAN Welcome Navman's 300 series GPS Sport. Tools provide an affordable and reliable way to track and store a variety of personal performance indicators. Please read this guide carefully and familiarize yourself with the interface and functions, as well as the intended use and limitations of the Navman X300 GPS Sport. Tool. This product complies with CE, FCC, Canada 210, and C-Tick regulations. Operation is subject to the following two conditions: (1) this device may not cause interference (2) this device must accept any interference, including interference that may cause undesired operation of the device. WARNING: Entering information or handling the Navman Sport. Tool while moving is unsafe and may cause you to be distracted or fail to observe safe practices necessary to avoid death, serious injury, collisions or accidents to you or others. Use the memory functions to review data when you are not moving. [. . . ] Press repeatedly until the screen appears as shown above. To set button beep status to start editing (setting status flashes). 1) Press 2) Press or to select On or OFF. 3) Press 4) Press to go to the next option, or hold to leave setup. 4. 1. 5 Set speed units Set units for speed (km/h or mph). km km/h SYSTEM SET m speed units Access this option If necessary, press and hold to turn the power on and enter setup. Press repeatedly until the screen appears as shown above. To set speed units 1) Press to start editing (speed units flash). 4) Press to go to the next option, or hold to leave setup. Note: Distance and altitude are displayed in units that correspond to user selected speed units. For example, if you select speed units `km/h', then distance is displayed in `km' and altitude in `m'. 1-14 X300 NAVMAN X300 - Setup 4. 1. 6 Set offset (set local time) This option lets you adjust the X300 to display local time*. You only need to do this once, unless operating the unit in a new time zone. (* By default the X300 displays GPS time. The X300 will perform all functions accurately without adjusting the offset to display your local time. ) Note: If you attempt to change the time offset before all GPS data are obtained, the screen displays `no GPS' and the antenna icon flashes until all GPS data are received. SYSTEM SET Access this option If necessary, press and hold to turn the power on and enter setup. Press repeatedly until the screen appears as shown above. To set local time to start editing (the screen now appears as shown 1) Press below). Press repeatedly until the screen appears as shown above. While in Speed mode · Press to store current lap data (the screen briefly shows the lap distance, lap number, and lap time that is being stored). (*Does not clear · Press and hold odometer. ) · Press to go to the next mode. 5. 1. 2 Speed (Average) mode This mode lets you monitor session distance and average speed. session distance average speed km km/h AVG To access this mode If necessary, press to turn the power on and start normal operation. Press repeatedly until the screen appears as shown above. While in Speed (Average) mode · Press to store current lap data (the screen briefly shows the lap distance, lap number, and lap time that is being stored). · Press and hold to clear all* session data. (*Does not clear odometer. ) · Press to go to the next mode. 1-18 X300 NAVMAN X300 - Normal operation 5. 1. 3 Speed (Maximum) mode This mode lets you monitor session distance and maximum speed. session distance maximum speed km km/h MAX Access this mode If necessary, press to turn the power on and start normal operation. Press repeatedly until the screen appears as shown above. While in Speed (Maximum) mode · Press to store current lap data (the screen briefly shows the lap distance, lap number, and lap time that is being stored). · Press and hold · Press to go to the next mode. 5. 1. 4 Odometer mode This mode shows total distance since odometer was last reset. total distance km 872 3 Access this mode If necessary, press to turn the power on and start normal operation. Press repeatedly until the screen appears as shown above. While in Odometer mode · Press to store current lap data (the screen briefly shows the lap distance, lap number, and lap time that is being stored). · Press and hold to clear odometer only. [. . . ] Session A session includes all time that the Sport. Tool has been actively operating since first start-up, or since the session data was last cleared. Clearing the session data removes all stored data from the previous session except the odometer value, which must be cleared separately. 8. 0 Copyright This publication and its contents are proprietary to Navman and are intended solely for the use of its clients to obtain information about the operation of Navman Sport. Tool products, it should not be used or distributed for any other purpose. Proprietary information and specifications relating to this document or the Navman Sport. Tool products are subject to change without notice. 1-26 X300 NAVMAN X300 ­ Warnings and disclaimers 9. 0 Additional warnings, disclaimers, and limitations on liability It is the user's sole responsibility to set-up and use the Navman GPS Sport. Tool (the Product) in a manner that will not cause accidents, personal injury or property damage to you or others. Entering information or handling the Product while moving is unsafe and may cause you to be distracted or fail to observe safe practices necessary to avoid death, serious injury, collisions or accidents to you or others. [. . . ]