User manual NEC AT-35

[. . . ] Caller ID Handsfree Business Telephone AT-35 USER GUIDE DISCLAIMER The material contained herein is subject to change without prior notice at the sole discretion of NEC Business Solutions Ltd. NEC Business Solutions Ltd. TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 LOCATION OF CONTROLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Package Contents Installing the Batteries Connecting the Telephone Connecting an Additional Device Wall Mounting INITIAL SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press VOLUME repeatedly to set the desired LCD contrast. Selecting the Ringing Volume Select from three ringing volume levels using the Ringing Volume Switch, L (low), M (mid), or H (high). Selecting the Ringing Tone There are 3 ringing tones to choose from ­ low, mid and high pitch. The selected ringing tone will play for approximately 2 seconds. Setting the Clock This telephone is equipped with a 24 hour clock. The clock is shown on the display while the phone is idle. To set the clock, follow the steps below. 2 seconds until the year appears flashing on the display. Advance up or down to the correct year by pressing the or keys. Press the SET TIME button to set the year and advance to the Month. Repeat this process to set the Month, Date, Hour and Minute. 8 INITIAL SETUP Setting the Flash Time The correct hookflash timing depends on the requirements of the PBX to which the telephone is connected. Dial 00 to 06 to select from the following list of hookflash timings. 00: 95ms 01: 100ms (Default) 02: 120ms 03: 180ms 04: 270ms 05: 300ms 06: 600ms 4. Dial #. Setting the PBX DIAL Code When installed as a PBX extension, a trunk access code is often required to precede external numbers that are dialled. The PBX DIAL key can automatically insert the PBX trunk access code at the front of a dialled number, when dialling from a One-Touch key, the IN List (Caller ID), or when Preview Dialling. The PBX trunk access code may differ from site to site, according to how the PBX is configured. To set the PBX DIAL code, follow the steps below. Dial 0 #. 9 BASIC OPERATION Making a Call using the Handset 1. Pick up the handset and wait for dial tone. Replace the handset when you finish the call. Dial the number you require (while on-hook). You may press the DELETE key to erase dialled digits one at a time. When you have finished dialling, pick up the handset. Replace the handset when you have finished the call. Adjust the volume if needed using the Handset Volume Control Switch. Making a Call using Speakerphone By using the SPEAKER key, you can make and receive calls without picking up the handset. [. . . ] Number of new calls. To Review the CLI Memory: 1. Press the SEARCH key until the "IN" icon is shown on the display. Advance up or down to review received CLI numbers by pressing the or keys. To view the most recent NEW CALL, press the key. [. . . ]