User manual NEC DSX-160 HARDWARE MANUAL

[. . . ] Empowered by Innovation Components Installation Upgrading from DS2000 to DSX-80/160 If upgrading from DS2000 to DSX-80/160, be sure to carefully review Upgrading DS2000 to DSX-80/160 (P/N 1093077) prior to the upgrade. Optional Equipment Specifications and Parts DSX-80/160 Hardware Manual P/N 1093096 Rev 2, June 2006 Printed in U. S. A. 01. 00. 00 For additional resources, visit our Technical Support site on the web at http://www. necdsx. com. This manual has been developed by NEC Unified Solutions, Inc. It is intended for the use of its customers and service personnel, and should be read in its entirety before attempting to install or program the system. Any comments or suggestions for improving this manual would be appreciated. Forward your remarks to: NEC Unified Solutions, Inc. [. . . ] At minimum, the installation site needs: One 66M1-50 block and Installation Cable (P/N 808920) for extensions and optional equipment. One 66M1-50 block and Installation Cable (P/N 808920) for analog lines. Depending on your card configuration and local codes, you may need an additional 66M1-50 block and Installation Cable (P/N 808920) for optional equipment. For each 66M1-50 block, punch down the Installation Cable in standard color-code order. Extensions 300-323 Shown 25-PAIR CABLE RJ61X BLOCK TERM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 1093096 - 18 COLOR CODE WHT-BLU BLU-WHT WHT-ORN ORN-WHT WHT-GRN GRN-WHT WHT-BRN BRN-WHT WHT-SLT SLT-WHT RED-BLU BLU-RED RED-ORN ORN-RED RED-GRN GRN-RED RED-BRN BRN-RED RED-SLT SLT-RED BLK-BLU BLU-BLK BLK-ORN ORN-BLK BLK-GRN GRN-BLK BLK-BRN BRN-BLK BLK-SLT SLT-BLK YEL-BLU BLU-YEL YEL-ORN ORN-YEL YEL-GRN GRN-YEL YEL-BRN BRN-YEL YEL-SLT SLT-YEL VIO-BLU BLU-VIO VIO-ORN ORN-VIO VIO-GRN GRN-VIO VIO-BRN BRN-VIO VIO-SLT SLT-VIO FUNCTION 300 300 301 301 302 302 303 303 304 304 305 305 306 306 307 307 308 308 309 309 310 310 311 311 312 312 313 313 314 314 315 315 316 316 317 317 318 318 319 319 320 320 321 321 322 322 323 323 NC NC T R T R T R T R T R T R T R T R T R T R T R T R T R T R T R T R T R T R T R T R T R T R T R T R RJ61X 5 4 3 6 2 7 1 8 5 4 3 6 2 7 1 8 5 4 3 6 2 7 1 8 5 4 3 6 2 7 1 8 5 4 3 6 2 7 1 8 5 4 3 6 2 7 1 8 16ESIU PCB PCB Location 1 2 3 4 Slot Cabinet shown To make your own cables, see Making Your Own Cables (page 39). 3 12 4 4 5 6 8 DSX-80 4-Slot KSU Shown 1 RJ61X Plug Figure 14: Connecting 16ESIU Digital Station Cards 32 Installation DSX-80/160 Hardware Manual Installing Cards Installing 16SLIU and 8SLIU Analog Station Cards The 16SLIU connects 16 analog telephones. The 8SLIU connects for 8 analog telephones. Turn to System Preparation (page 21) to be sure you haven't exceeded the allowable system load factor. Plug a SLIU Card into any available slot from CN2-CN8. - You should reserve CN1 for a 16ESIU Card. Set the mode switch on each installed SLIU Card to RUN Installation 9 10 30 96 3 -4 DSX-80 4-Slot KSU Shown Figure 15: Installing a 16SLIU or 8SLIU Analog Station Card DSX-80/160 Hardware Manual Installation 33 Installing Cards Connecting 16SLIU and 8SLIU Cards The SLIU Card, just like the COI and16ESIU Cards, uses 8-pin mod jacks to connect extensions. Using the Installation Cable (P/N 808920) makes it easy to connect the cards to standard 66M1-50 connecting blocks. These cables have six 8-pin modular jacks on one end and are unterminated on the other. At minimum, the installation site needs: One 66M1-50 block and Installation Cable (P/N 808920) for extensions and optional equipment. One 66M1-50 block and Installation Cable (P/N 808920) for analog lines. Depending on your card configuration and local codes, you may need an additional 66M1-50 block and Installation Cable (P/N 808920) for optional equipment. To punch down the cables: For each 66M1-50 block, punch down the Installation Cable in standard color-code order. Extensions 316-331 Shown 25-PAIR CABLE RJ61X BLOCK TERM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 1093096 - 38 COLOR CODE WHT-BLU BLU-WHT WHT-ORN ORN-WHT WHT-GRN GRN-WHT WHT-BRN BRN-WHT WHT-SLT SLT-WHT RED-BLU BLU-RED RED-ORN ORN-RED RED-GRN GRN-RED RED-BRN BRN-RED RED-SLT SLT-RED BLK-BLU BLU-BLK BLK-ORN ORN-BLK BLK-GRN GRN-BLK BLK-BRN BRN-BLK BLK-SLT SLT-BLK YEL-BLU BLU-YEL YEL-ORN ORN-YEL YEL-GRN GRN-YEL YEL-BRN BRN-YEL YEL-SLT SLT-YEL VIO-BLU BLU-VIO VIO-ORN ORN-VIO VIO-GRN GRN-VIO VIO-BRN BRN-VIO VIO-SLT SLT-VIO FUNCTION 316 316 317 317 318 318 319 319 320 320 321 321 322 322 323 323 324 324 325 325 326 326 327 327 328 328 329 329 330 330 331 331 T R T R T R T R T R T R T R T R T R T R T R T R T R T R T R T R RJ61X 5 4 3 6 2 7 1 8 5 4 3 6 2 7 1 8 5 4 3 6 2 7 1 8 5 4 3 6 2 7 1 8 5 4 3 6 2 7 1 8 5 4 3 6 2 7 1 8 16SLIU PCB PCB Location 1 2 3 4 Slot Cabinet shown 4 3 12 4 To make your own cables, see Making Your Own Cables (page 39). 5 6 8 DSX-80 4-Slot KSU Shown 1 RJ61X Plug NC NC Figure 16: Connecting 16SLIU and 8SLIU Cards 34 Installation DSX-80/160 Hardware Manual Installing Cards Installing 16COIU and 8COIU Analog Line Cards The 16COIU connects 16 analog loop start lines. The 8SCOIU connects 8 analog loop start lines. Turn to System Preparation (page 21) to be sure you haven't exceeded the allowable system load factor. Plug a COIU Card into any available slot from CN2-CN8. - You should reserve CN1 for a 16ESIU Card. Set the mode switch on each installed COIU Card to Run. Installation 10 93 09 6 7 -1 Notes: · · The system will respond to telco ring signal in the range of 42-103 VAC @ 20 Hz. Telco battery must be 44-56 VDC. DSX-80 4-Slot KSU Shown Figure 17: Installing a 16COIU or 8COIU Analog Line Card DSX-80/160 Hardware Manual Installation 35 Installing Cards Connecting 16COIU and 8COIU Cards The COIU Card, just like the SLI and16ESIU Cards, uses 8-pin mod jacks to connect extensions. Using the Installation Cable (P/N 808920) makes it easy to connect the cards to standard 66M1-50 connecting blocks. [. . . ] Refer to the Standard Practices Manual for further information. In direct sunlight or in hot, cold or humid places. In dusty areas or in areas where sulfuric gases are produced. In places where shocks or vibrations are frequent or strong. [. . . ]