User manual NEC DTL-8R-1

[. . . ] Dterm Cordless DECT ® OWNER'S MANUAL DTL-8R-1 INT-2070 (DECT) DOCUMENT REVISION 1 Contents of this manual are subject to change without prior notice at the discretion of NEC Unified Solutions, Inc. This document has been prepared for the use of employees and customers of NEC Unified Solutions, Inc. and may not be reproduced without prior written approval of NEC Unified Solutions, Inc. Dterm is a registered trademark of NEC Corporation. Copyright 2007 NEC Infrontia, Inc. [. . . ] Push the MUTE(Menu) key to save the setting. The Handset gives a confirmation tone. 4. 4 Charger Unit The Charger Unit is used to recharge the batteries in the handset. 21 22 23 21. Optional Battery Charging LED Figure 2-5 Charging Unit Controls and Functions ___________________________________________________________________________________ Owner's Guide 2-7 Document Revision 1 Dterm Cordless DECT ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ 2-8 About the Dterm Cordless DECT Chapter 3 Installation SECTION 1 SELECTING A LOCATION Select a location for the Dterm Cordless DECT to avoid excessive heat or humidity. The base unit of the Dterm Cordless DECT can be placed on a desk or tabletop near a standard 120 Vac outlet and telephone line jack. The base unit can also be mounted on a standard wall plate using the wall mount adapter. Keep the base unit and handset away from sources of electrical noise (motors, fluorescent lighting, computers, PC monitor). Refer to Chapter 1 Specifications and Safety Information for a complete discussion of safety precautions. SECTION 2 INSTALLATION PRECAUTIONS To ensure optimum performance follow these guidelines. Each base unit must be placed at least 20 feet apart. Always place the base unit on top of a desk or on higher shelves. Avoid locations surrounded by metal surfaces. Place the base away from any electrical component such as a PC, monitor and other telephone. SECTION 3 CONNECTING THE TELEPHONE CORDS When connecting the telephone cords, observe the following precautions. Never install telephone wiring during a lightning storm. Never touch bare telephone wires or terminals unless the telephone line has been disconnected at the network interface. Use caution when installing or modifying telephone lines. ___________________________________________________________________________________ Owner's Guide 3-1 Document Revision 1 Dterm Cordless DECT ___________________________________________________________________________________ To connect the telephone cords: 1. Connect the cord from the telephone jack to the Line In on the Dterm Cordless DECT. Figure 3-1 Connecting Telephone Cords to the Telephone Jack 2. Connect a qualified NEC digital Multiline Terminal to the Dterm Cordless DECT. Line "OUT" To DTU, DTP, DTH, DTR and DTL Multiline Telephones Figure 3-2 Connecting the Dterm Cordless DECT to the Multiline Terminal ___________________________________________________________________________________ 3-2 Installation Dterm Cordless DECT Document Revision 1 ___________________________________________________________________________________ SECTION 4 APPLYING POWER TO THE CHARGING UNIT The unique design of the telephone allows the user to place the handset in the charging unit with or without the belt clip attached. The charging unit can charge a second battery with or without the handset being charged. The battery packs can automatically be recharged either in or out of the handset. Figure 3-3 Applying Power to the Charging Unit Use only the supplied AC adapter for the charging unit. The AC adapter furnished with this telephone may be equipped with a polarized line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, try reversing the plug. If you cannot plug the AC adapter into the outlet, the outlet may need to be replaced. Route the power cord where it will not create a trip hazard, or where it could become chafed and create a fire or other electrical hazards. ___________________________________________________________________________________ Owner's Guide 3-3 Document Revision 1 Dterm Cordless DECT ___________________________________________________________________________________ Figure 3-4 Polarized Plug SECTION 5 WALL INSTALLATION 5. 1 Mounting the Base to a Standard Wall Plate The base unit is designed to be mounted on standard wall plate. To attach the wall mount stand to the base unit: 1. Slide the wall mount stand into the notches at the top of the base unit. [. . . ] The Handset Cancel Menu setting is activated and the handset goes into Standby Mode. 2. 17 Changing Ringer Type To change the ringer type: 1. Press the MUTE(Menu) key in Standby Mode; the LCD shows the menu list. Ch a n g e End of Ri n g e r Type Ra n g e Al ar m 2. If needed, select "Change Ringer Type" by pressing the Volume Up or Volume Down key and pressing the MUTE(Menu) key. Otherwise, if the option is already selected, press only the MUTE(Menu) key. ___________________________________________________________________________________ Owner's Guide 6 - 15 Document Revision 1 Dterm Cordless DECT ___________________________________________________________________________________ 3. [. . . ]