User manual NEC GT2150

[. . . ] LCD Projector GT2150 User's Manual LIMITED WARRANTY Except as specified below, the warranty that may be provided by the dealer covers all defects in material or workmanship in this product. The following are not covered by the warranty: 1. Any product on which the serial number has been defaced, modified or removed. Damage, deterioration or malfunction resulting from; a. [. . . ] Adjust the lens focus by using the FOCUS button on the projector cabinet or the remote control. NOTE: If the physical (vertical) alignment of the projector is not correct, adjust the height of the feet. If there is any keystone distortion, use Keystone adjustment to correct and save the settings on each projector. An image is projected from the master projector. See page E-50 for Link mode. E ­ 16 Projector Orientation 6) Link Mode Setting 6-1 Assign a unique Projector ID for each projector. Select [Projector Options] [Setup] [Page 5] [Projector ID]. Specify a unique projector ID for each projector. 6-2 Select the same communication speed for all the projectors. Select [Projector Options] [Setup] [Page 5] [Communication Speed]. See page E-50 for setting the communication speed. Select the appropriate speed between 4800 and 38400. 6-3 Set the Link Mode on each projector. Select [Projector Options] [Link Mode]. First select [Slave] on the slave projector. Select [Master] on the master projector. 6-4 Project a source image from all projectors 6-4-1. Check to see if the imags on the master projector are displayed in syncronization with the ones on the other slave projector while the projectors are in link mode. NOTE: Registering signals is not possible in the Link mode. To register a signal, first set "Link Mode" to "Standalone" on the menu and then repeat the above steps from 3. If you select an unregistered signal, the master projector displays the image, but the slave projector doesn't. To view the information on the currently displayed signal, select [Help] [Source Information] [Page1]. 6-5 Make adjustments to the slave projector. NOTE: See "List of Menu Items Available on Link Mode" on page E-62 for more information. [. . . ] The LCD panel may have pixel failures at the rate of 0. 01% or less. We provide information about our projectors through the World Wide Web at http://www. nec-pj. com/ The specifications are subject to change without notice. E ­ 58 9. Appendix Cabinet Dimensions 7. 7" (195) 16. 5" (419) 8. 2" (209) 19. 4" (494) Lens center PC CARD Lens center 4. 6" (118) IN IN PC CONTROL REMOTE 2 OUT OUT REMOTE 1 SC. TRIGGER AC IN Optional Accessories Lens Optional lens (Fixed short throw: 1. 0) Optional lens (Zoom: 1. 3 ­ 1. 6) Optional lens (Zoom: 1. 8 ­ 2. 4) Optional lens (Zoom: 3. 4 ­ 5. 2) Lamp Ceiling Mount Expansion module Remote Control Replacement lamp Kit for ceiling mount installation LAN module Presentation remote control kit GT10RL GT13ZL GT19ZL GT34ZL GT50LP GT50CM GT50LAN PR51KIT E ­ 59 FOCUS ZOOM LEFT LENS SHIFT DOWN UP RIGHT EN TE R SELECT MENU CAN LAMP CE STATUS POWER SOURCE AUTO ADJUST ON/STAND BY L DVI DIGITAL L/MONO R DVI DIGITAL L/MONO R OUTPUT ANALOG RGB 2 RGB 1 R/Cr G/Y B/Cb VIDEO 1 L/MONO VIDEO 2 L/MONO R R H/HV L/MONO R V L/MONO R S-VIDEO AUDIO OUT Unit = inch (mm) D-Sub Pin Assignments Mini D-Sub 15 Pin Connector (RGB2) Signal Level Video signal : 0. 7Vp-p (Analog) Sync signal : TTL level 4321 10 9 8 7 6 15 14 13 12 11 5 Pin No. [. . . ]