User manual NEC HT1100

[. . . ] HT1100 Entertainment Projector User's Manual English Deutsch Français Italiano Español Svenska IMPORTANT INFORMATION Safety Cautions Precautions Please read this manual carefully before using your NEC HT1100 Projector and keep the manual handy for future reference. Your serial number is located on the bottom of your projector. Record it here: CAUTION To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. [. . . ] Black Expansion Minimizes blacks that appear more like shades of gray to provide a true black and white image at high contrast. Off/1/2/3/4/5 Selecting Aspect Ratio [Aspect Ratio] (not available for Viewer) Aspect Ratio allows you to select the best Aspect mode to display your source image. When screen size 4:3 is selected for the source, the following selections will display: Normal . . . . . . . . . . . Standard 4:3 Aspect. NOTE: This feature is not available for Scart, 480p, 576p, HDTV and RGB signals. Contrast Enhancement This option allows you to provide a high contrast image in a bright scene. ­3/­2/­1/Off/1/2/3 Zoom . . . . . . . . . . . . . Top and bottom reduced to display with black borders on top and bottom. When screen size 16:9 and Anamorphic are selected for the source, the following selections will display: Normal . . . . . . . . . . . Stretched to display in 16:9 aspect ratio. Available for 16:9 only. NOTE: This feature is available for TV standard signals only. NOTE: You can adjust image positions vertically for source with black borders. See page E-23 for setting image positions. Copyright Please note that using this projector for the purpose of commercial gain or the attraction of public attention in a venue such as a coffee shop or hotel and employing compression or expansion of the screen image with an "Aspect Ratio" or "Screen" setting may raise concern about the infringement of copyrights which are protected by copyright law. NOTE: During 3D Reform adjustment, "Aspect Ratio" may not be available. Should this happen, first reset the 3D Reform data and then do setting again. Changing the aspect ratio can limit 3D Reform in its adjustable range. E-30 When screen size 4:3 is selected for the source, the following selections will display. mode input 480i/576i DVD progressive 480p/576p These are the same signals. 720p 1080i 1080p PC(RGB) Normal Zoom Cinema V-Zoom When screen size 16:9 and Anamorphic (*) are selected for the source, the following selections will display. mode input 480i/576i DVD progressive 480p/576p These are the same signals. 720p 1080i 1080p PC(RGB) Normal Full Zoom Stadium * A commercially available anamorphic lens is needed. E-31 Masking Unwanted Area [Blanking] This feature allows you to mask any unwanted area of the screen image. Adjust the Top, Bottom, Left or Right blanking with the SELECT or button. Adjusting Position and Clock [Position / Clock] This allows you to manually adjust the image horizontally and vertically, and adjust Clock and Phase. Horizontal/Vertical Position: Adjusts the image location horizontally and vertically using the SELECT and buttons. Use this item to fine tune the computer image or to remove any vertical banding that might appear. This function adjusts the clock frequencies that eliminate the horizontal banding in the image. Press the SELECT and buttons until the banding disappears. This adjustment may be necessary when you connect your computer for the first time. Use this item to adjust the clock phase or to reduce video noise, dot interference or cross talk. (This is evident when part of your image appears to be shimmering. ) Use the SELECT and buttons to adjust the image. Use "Phase" only after the "Clock" is complete. [. . . ] w/Valid Date : (1) Credit Card (2) Travelers Cheque (3) Cash (1) Repair and Return (2) Loan unit E-54 Condition of your TravelCare Service Program Enduser is requested to understand following conditions of TravelCare Service Program and complete the necessary information on the application sheet. Service Options: There are 3 types of "Service" available. Enduser has to understand following condition and is required to fill in the Application Sheet. 1) Repair and Return: The 'Faulty unit' is sent or collected from the customer. [. . . ]