User manual NEC HT410

[. . . ] Entertainment Projector HT510/HT410 User's Manual English Deutsch Français Italiano Español Svenska LIMITED WARRANTY Except as specified below, the warranty that may be provided by the dealer covers all defects in material or workmanship in this product. The following are not covered by the warranty: 1. Any product on which the serial number has been defaced, modified or removed. Damage, deterioration or malfunction resulting from; a. [. . . ] INSTALLATION AND CONNECTIONS Connecting the Supplied Power Cable Connect the supplied power cable to the projector. First connect the supplied power cable's two-pin plug to the AC IN of the projector, and then connect the other plug of the supplied power cable in the wall outlet. CO NTRO L CAUTION Do not unplug the power cable from the wall outlet under any one of the following circumstances. Doing so can cause damage to the projector: * While the projector is turned on. (The cooling fans continue to work for 60 seconds after the projector is turned off). E-20 ON /STA ND BY PO WER ST AT US LA MP AU AD TO J. S-VID EO IN L/m Cb Y O IN /Pb ono DIO IN R VIDE r Cr/PENT IN ON AU CO UT ER IN AU DIO IN MP CO MP AC IN 3. PROJECTING AN IMAGE (BASIC OPERATION) 3. PROJECTING AN IMAGE (BASIC OPERATION) This section describes how to turn on the projector and to project a picture onto the screen. Turning on the Projector NOTE: · The projector has two power switches: a main power switch and an ON/STAND BY button. · When plugging in or unplugging the supplied power cable, make sure that the main power switch is pushed to the off (O) position. Failure to do so may cause damage to the projector. To turn on the main power to the projector, press the Main Power switch to the on ( I ) position. The POWER indicator will light orange. LAMP STATUS POWER DEO S-VI IN L/mo Cb/P Y b R no L TRO CON Before you turn on your projector, ensure that the computer or video source is turned on and that your lens cap is removed. Only after you press the ON/STAND BY button on the projector cabinet or POWER ON button on the remote control for a minimum of 2 seconds will the power indicator turn to green and the projector become ready to use. Cabinet controls Remote control OFF LAMP STATUS POWER POWER ON COMPONENT COMPUTER VIDEO SOURCE C-VIDEO COMP. AUTO ADJ. SELECT S-VIDEO ON/STAND BY AUTO ADJ. AUTO MENU Standby LAMP STATUS POWER Blinking LAMP STATUS POWER Power On LAMP STATUS POWER Steady orange light Blinking green light Steady green light See page E-49 for more details. NOTE: The POWER and STATUS (LED) indicators blinking green at the same time indicates the main power was interrupted during previous operation. Wait for 60 seconds (cooling period) to see if the lamp turns on by itself. E-21 3. PROJECTING AN IMAGE (BASIC OPERATION) Note on Startup screen (Menu Language Select screen) When you first turn on the projector, you will get the Startup screen. This screen gives you the opportunity to select one of the 9 menu languages. To select a menu language, follow these steps: 1. Use the SELECT or button to select one of the 9 languages for the menu. Cabinet controls Remote control MENU LAMP STATUS POWER SOURCE SELECT ON/STAND BY AUTO ADJ. ENTER EXIT NOISE RED. Press the ENTER button to execute the selection. Cabinet controls Remote control MENU LAMP STATUS POWER SOURCE SELECT ENTER ON/STAND BY AUTO ADJ. EXIT NOISE RED. PICTURE OFF TIMER After this has been done, you can proceed to the menu operation. If you want, you can select the menu language later. See "Language" on page E-38. NOTE: Immediately after turning on the projector, screen flicker may occur. Wait 3 to 5 minutes until the lamp lighting is stabilized. When the Lamp mode is set to Eco, the Lamp indicator will light green. [. . . ] Enduser has to understand following condition and is required to fill in the Application Sheet. 1) Repair and Return: The 'Faulty unit' is sent or collected from the customer. It is repaired and returned within 10 days to the customer, excluding transport time. There may have a case, repair and return can't be done by NEC Authorized Service Station, because of shortage of spare parts due to same model is not sold in the territory. [. . . ]