User manual NEC VERSA 6060

[. . . ] NEC Computer Systems Division, A Division of Packard Bell NEC, Inc. DECLARATION OF CONFORMITY We, the Responsible Party NEC Computer Systems Division Packard Bell NEC, Inc. 1414 Massachusetts Avenue Boxboro, MA 01719 (508) 264-8000 declare that the product NEC V6060 Series is in conformity with part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. PROPRIETARY NOTICE AND LIABILITY DISCLAIMER The information disclosed in this document, including all designs and related materials, is the valuable property of NEC Computer Systems Division, Packard Bell NEC, Inc. NECCSD and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights to this document, including all design, manufacturing, reproduction, use, and sales rights thereto, except to the extent said rights are expressly granted to others. [. . . ] Warm Swapping allows you to replace devices while your system is in Suspend mode. You do not have to reboot your system to reconfigure for the new device. To warm swap place the system in Suspend mode, by pressing the Suspend/Resume (S/R) button. Then follow the instructions to replace either the diskette drive or CD-ROM reader. 4-6 Using Your NEC Versa Locating the VersaBay II In addition to the CD-ROM reader, the VersaBay II accepts the following options: T T a second battery pack a second hard disk drive. See the NEC Versa Tools Catalog or your authorized NEC dealer for details about these VersaBay II options. Removing a Device from the VersaBay II Use the following steps to remove the standard diskette drive (or other device) from the VersaBay II. 1. Make sure the NEC Versa is powered off or in Suspend mode, all op- tions are disconnected, and the LCD panel is closed. 2. Turn the system upside down with the front facing you. Locate the VersaBay II release latches on the bottom of the unit. Using Your NEC Versa 4-7 VersaBay II release latches 4. Slide the front latch towards the hard disk drive side of the system, and hold it. 5. Push the middle latch towards you until the drive pops part way out of the unit. 6. Continue to hold the latch near the front of the system to the left, and pull the device the rest of the way out of the system. If you release the front latch before completely removing the device, the device casing may catch on the inside of the latch. NOTE 4-8 Using Your NEC Versa Releasing the device Installing a Device in the VersaBay II Use the following steps to install a device in the VersaBay II. Specifically, these steps show how to install the 20X CD-ROM reader that ships standard with the system. If you install a hard disk drive from a Versa model E, V, M, or P in the VersaBay II, it becomes the master drive from which the system will boot. Your system must be powered off or placed in suspend mode before removing or inserting devices in the VersaBay II. To use a hard disk drive in the VersaBay II, the drive must be connected to the appropriate adapter. See the NEC Versa Tools Catalog or your authorized NEC dealer for details about the Hard Disk Drive Adapter Kit. NOTE 1. Locate the switch labeled S (slave) and M (master) on your CD-ROM pack. Using Your NEC Versa 4-9 2. The slave/master switch default setting is S. Keep this default setting even if you are booting to a bootable CD-ROM. 3. Align the CD-ROM reader in the VersaBay II and push it in until it locks into place. Inserting the CD-ROM reader 4. Power on the system or return from Suspend mode. 4-10 Using Your NEC Versa Customizing Your System with the VersaBay II It's easy to customize your NEC Versa using the VersaBay II. If you find you require additional hard disk space or increased battery longevity, simply remove the standard device and plug in an optional hard disk drive or battery. If you install a second hard disk drive in the VersaBay II, it can be set to either master or slave. However, if you use a 19mm hard disk drive from a previous NEC Versa model, the drive is automatically set to master. (The Master drive is the drive from which the system boots. ) NOTE Add another hard disk drive, or second Li-Ion battery pack as follows. 1. [. . . ] A single USB port can be used to connect up to 126 peripheral devices, such as mice, modems, and keyboards. USB also supports Plug-and-Play installation and hot plugging. It is expected to be commonplace sometime in 1997 and to eventually completely replace serial and parallel ports. VGA V Video Graphics Array. Graphics technology that supports up to 256 colors and a graphics resolution of 640 by 480 pixels. volatile memory Storage media that loses its data when system power is turned off. [. . . ]