User manual NEC WPA001

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual NEC WPA001. We hope that this NEC WPA001 user guide will be useful to you.

Lastmanuals help download the user guide NEC WPA001.

Download

You may also download the following manuals related to this product:

NEC WPA001 INSTALLATION GUIDE (556 ko)

Manual abstract: user guide NEC WPA001

Detailed instructions for use are in the User's Guide.

 [. . . ] WMS Guide
For Hardware Settings

507100-02-09-W-E-111105-01

Copyright
© 2005,  NewSoft Technology Corp. No portion of this document may be copied or reproduced in any manner without prior written permission from NewSoft Technology Corp. (NewSoft) NewSoft has no warranties to this documentation and disclaims any implied warranty of merchantability or fitness for a particular purpose.  [. . . ] Click Internet Protocol (TCP/IP) and change the IP address to a number between 192. 168. 168. 2 and 192. 168. 168. 254. Type 255. 255. 255. 0 for the Subnet mask. 

Example of an IP Address

2

Starting up the WMS

3. Use your Internet browser to open http://192. 168. 168. 30/ to see the configuration page for the WMS Receiver Box. Type "admin" as User name,  and "1234" for Password. 

You must disable your firewall and proxy settings. If the configuration page doesn't open,  turn the device off and on to reset it. 

3

Setting up the WMS

Chapter 2

Setting up the WMS

The main menu has all the controls for configuring your WMS 100. 

Status
Under Status,  you can view the current settings of the Ethernet LAN or WLAN. Click General and LAN to see the Device Information and LAN Settings,  including the MAC and IP address. 

WLAN settings can be seen by clicking WLAN. · The Region setting will tell you if 802. 11a Ad-hoc mode is supported or not. For region ETSI,  the 802. 11a 5 GHz Ad-hoc mode is not supported. · The Link Status may be Up,  indicating that it is connected to a WMS Sender,  or Down,  indicating that it is available for connecting. 

4

Setting up the WMS

Setup
Under Setup,  you can choose LAN or WLAN. LAN is used to choose DHCP or static for the IP address. · If you select DHCP,  you have to find the IP address by using another tool or by asking your MIS department if you ever need to reconfigure. An alternative would be to push and hold the Reset button on the WMS Receiver Box for more than 5 seconds to revert to the factory default IP address. · If you change to another network segment,  remember to configure the computer to the same network segment. 

5

Setting up the WMS

Use WLAN to change these settings. · · Country is used to identify the WLAN card set. Region is used to identify the radio certification. · · SSID is defaulted to use "WMS100-IMAGE".  [. . . ] You can press the Reset button for more than 5 seconds to get the default user name and password if you forget it. Only English alphanumeric characters are accepted for passwords. 

7

Setting up the WMS

Download WMS
Click to download the WMS software. The program will be installed immediately. 

Site Survey
This function is used to connect to any other SSID groups,  especially Access Point. 

8 [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE NEC WPA001

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual NEC WPA001 will begin.