User manual NEC XG85-XG135LC

[. . . ] MultiSync XG85 MultiSync XG135LC Large Screen MultiSync Projection Monitor Installation Manual Model Number: XG-852/XG-1352 XG-852G/XG-1352G The projector must be installed by trained personnel CONTENTS INSTALLATION SET-UP INSTRUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Before Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Carrying the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Note on Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Sizes not found between 48(60)and 240(300)inches are determined by the following formulae: Units=inches W"=Screen H-Width A = (25/96 W" 12. 5) 5. 47 71. 85 Units=mm W"=Screen H-Width A = (25/96 W" 12. 5) 141 1825 Screen size (Diagonal) 60­89" 90­129" 130­179" 180­300" 11. 8° 12. 2° 12. 4° 12. 6° 10 654321 654321 654321 654321 654321 654321 654321 PROJECTION CONFIGURATION CHANGE. Before Installation Change The projector is electrically and mechanically set for 100 inch diagonal screen, front throw ceiling mount and a projection angle of 12. 4° (XG85)/12. 2°(XG135LC). If your application is different from the factory setting(for example, ceiling to floor and screen size between 60 and 300 inch), you will have to reconfigure the projector for your application. Follow the change procedures according to the instructions below. For XG85 To change screen size only: 1) Set the focus ring to the proper position. (See pages15 and 16. ) For 100" screen size R ­ A-3, B-3 G ­ A-1, B-3 B ­ A-3, B-3 For 120" screen size R ­ A-3, B-3 G ­ A-1, B-3 B ­ A-3, B-3 For 180" screen size R ­ A-5, B-5 G ­ A-1, B-5 B ­ A-5, B-5 To change to the ceiling mount system (rear) 1) Reverse the scan. (See page 14. ) 2) Set the focus ring to the proper position. (See pages 16 and 17. ) For 100" screen size R ­ A-3, B-3 G ­ A-1, B-3 B ­ A-3, B-3 For 120" screen size R ­ A-3, B-3 G ­ A-1, B-3 B ­ A-3, B-3 For 180" screen size R ­ A-5, B-5 G ­ A-1, B-5 B ­ A-5, B-5 2) Adjust the angle of the CRT's. (See page 16. ) For 100" screen size Move the CRT to the 100 position For 120­180" screen size and the other screen sizes Move the CRT to the 120, 180, or 60­300 position 3) Adjust the angle of the CRT's. (See page 17. ) For 100" screen size Move the CRT to the 100 position For 120­180" screen size and the other screen sizes Move the CRT to the 120, 180, or 60­300 position To change to the desk top system (front) 1) Reverse the scan. (See page 14. ) 4) Select an installation from the PJ ORIENTATION menu in the SETTING menu. (See "Projection Type Selection" in the setup manual. ) 2) Set the focus ring to the proper position. (See pages 15 and 16. ) For 100" screen size R ­ A-3, B-3 G ­ A-1, B-3 B ­ A-3, B-3 For 120" screen size R ­ A-3, B-3 G ­ A-1, B-3 B ­ A-3, B-3 For 180" screen size R ­ A-5, B-5 G ­ A-1, B-5 B ­ A-5, B-5 To change to the desk top system (rear, 0 projection angle) 1) Set the focus ring to the proper position. (See pages 16 and 17. ) For 100" screen size R ­ A-3, B-3 G ­ A-1, B-3 B ­ A-3, B-3 For 120" screen size R ­ A-3, B-3 G ­ A-1, B-3 B ­ A-3, B-3 For 180" screen size R ­ A-5, B-5 G ­ A-1, B-5 B ­ A-5, B-5 3) Adjust the angle of the CRT's. (See page 16. ) For 100" screen size Move the CRT to the 100 position For 120­180" screen size and the other screen sizes Move the CRT to the 120, 180, or 60­300 position 2) Adjust the angle of the CRT's (See page 17. ) For 100" screen size Move the CRT to the 100 position For 120­180" screen size and the other screen sizes Move the CRT to the 120, 180, or 60­300 position 4) Select an installation from the PJ ORIENTATION menu in the SETTING menu. (See "Projection Type Selection" in the setup manual. ) 3) Select an installation from the PJ ORIENTATION menu in the SETTING menu. (See "Projection Type Selection" in the setup manual. ) 11 PROJECTION CONFIGURATION CHANGE For XG135LC To change screen size only: 1) Set the focus ring to the proper position. (See page 17. ) For 100" screen size R ­ H-3, V-3 G ­ H-5, V-3 B ­ H-3, V-3 For 120" screen size R ­ H-3. 5, V-2. 5 G ­ H-5, V-2. 5 B ­ H-3. 5, V-2. 5 For 180" screen size R ­ H-3. 5, V-2. 5 G ­ H-5, V-2. 5 B ­ H-3. 5, V-2. 5 To change to the ceiling mount system (rear) 1) Reverse the scan. (See page 14. ) 2) Set the focus ring to the proper position. (See page 17. ) For 100" screen size R ­ H-3, V-3 G ­ H-5, V-3 B ­ H-3, V-3 For 120" screen size R ­ H-3. 5, V-2. 5 G ­ H-5, V-2. 5 B ­ H-3. 5, V-2. 5 For 180" screen size R ­ H-3. 5, V-2. 5 G ­ H-5, V-2. 5 B ­ H-3. 5, V-2. 5 2) Adjust the angle of the CRT's. (See page 18. ) For 100" screen size Move the CRT to the 100 position For 120­180" screen size and the other screen sizes Move the CRT to the 120, 180, or 60­300 position 3) Adjust the angle of the CRT's. (See page 18. ) For 100" screen size Move the CRT to the 100 position For 120­180" screen size Move the CRT to the 120, or 180. To change to the desk top system (front) 1) Reverse the scan. (See page 14. ) 4) Select an installation from the PJ ORIENTATION menu in the SETTING menu. [. . . ] After doing this, adjust the lens focus (see the next page). Then tighten the screws E. F E D D E F 60-3 00 100 120 180 60-3 180 120 100 00 C C Metal impression stamp screen size Range of screen size (diagonal) 60-300 60"-300" 100 100" 120 120" 180 180" 16 PROJECTION CONFIGURATION CHANGE Screen Size Change(Adjusting Focus Rings and CRT Angle) for XG135LC · Adjusting Focus Rings for the XG135LC There are three sets of adjusting focus rings, two between each CRT and lens. These focus rings are used for maintaining optimum edge focus for the various screen sizes and projection angles. *When setting the focus rings or changing CRT angle, you must first remove the front panel. [. . . ]