User manual NEC XG85RP-CH

[. . . ] MultiSync XG85RP/XG85RPW MultiSync XG135RP Large Screen MultiSync Rear Projection System Set-Up Manual Model Number: XG-852C/XG-1352C The projector must be assembled by qualified installation technicians. 2 654321 654321 654321 654321 654321 654321 654321 CONTENTS. SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Displaying the Various Setting Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Projection Type Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Connecting to the Switcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To delete all the entered digits, hold down the CTL button then press the NORMAL button. 3) If the entered passcode is correct, the "ADJUST" menu is displayed. NOTE: If the passcode is not correct, the "WARNING DIFFERENT PASSCODE!!" message is displayed and you are required to enter the correct passcode. 3 Proceed to each adjustment and setting. PASSCODE? 68 PASSCODE Registering Passcode When the projector is shipped from the factory, no passcode is registered. If you want to use the passcode option, you must register a passcode. To register a new passcode, proceed as follows: 1 Press the ADJUST button. · The "ADJUST" menu will be displayed. 2 Use the CURSOR or button to highlight the "7/ PASSCODE" line. Press ENTER to display the "PASSCODE" menu. You can also select the "PASSCODE" menu directly by pressing the INPUT "7" button. ­ 1 2 3 4 5 6 7 8 9 A / / / / / / / / / DJUST ­ SIGNAL ENTRY FOCUS ALIGNMENT CONVERGENCE KELVIN R, G, B GAIN PASSCODE OPTION REF. ADJUST 3 Use the CURSOR or button to select "ENTRY". Press ENTER to display the "NEW PASSCODE?" menu. You can also select the "NEW PASSCODE?" menu directly by pressing the INPUT "1" button. ­ PASSCODE ­ 1 / ENTRY 2 / DISABLE 4 Enter a four digit passcode using the "1" through "0" buttons. 1) Each time you press the INPUT button, an asterisk will appear under the "NEW PASSCODE?" message. NOTE: "0000" and "9999" cannot be used as a passcode. 2) Once you have finished entering your four digit passcode, press ENTER to store the code. NOTE: If you have made an error, press the NORMAL button to delete the asterisk "". To delete all the entered digits, hold down the CTL button then press the NORMAL button. 3) If the passcode has been entered correctly, the "CONFIRM NEW PASSCODE?" menu will be displayed. NOTE: If the passcode is not entered correctly, the "WARNING PASSCODE!!" message will be displayed. You will be required to enter the passcode correctly. NEW PASSCODE?­­­­ 69 PASSCODE 5 Enter the new passcode again. 1) Each time you press the INPUT button, an asterisk will appear under the "CONFIRM NEW PASSCODE?" message. 2) Once you have finished entering the new four digit passcode, press ENTER. [. . . ] Passcode change completed The D-CONV PWB is engaged in computational processing. D-CONV PWB communication error D-CONV PWB communication error Signal is being deleting from INPUT LIST. ENTRY COPY completed There is no space for signals No. 51 and later in Input List when "NEW" is selected from "STORE?" menu. [. . . ]