User manual NEFF GM240130 annexe 1

[. . . ] en Short and precise: everything your dishwasher needs. . . However, before using the device for the first time, read the Installation and Instruction Manual thoroughly! Interesting Facts For The Operation Before first use ­ Select the display language (see instruction manual) ­ Fill in salt and rinse aid (see below) ­ Set Softening System (see instruction manual) The display gives optical character information on the programmes, options, and settings as well as actions available. d Menu OK ­< Auto Wash >+ Start ­ d Main switch : Switch on the device : Select options, store changed value : Select programmes and settings : Start programme Quick Guide Dishwasher This dishwasher is equipped with touch buttons. A gentle touch starts the function. ­ Menu/OK ­ and + ­ Start The luminous arrows indicate whether you are able to select among other options using ­ or +. Fill in salt Not required if softening system set to "0". [. . . ] In practice, deviations are possible. Duration: hs/mins Energy Consumption: kWh Water Consumption: litres 1:40-2:20 1, 20-1, 60 16-23 1:40-2:40 1, 00-1, 30 12-20 1:20-1:50 0, 80-1, 10 10-17 0:30 0, 80 10 0:19 0, 10 4 Start programme Press Start button. Here goes . . . Options/Basic Settings Select and store: Menu/OK; Set: ­/+. Standard programmes Standard Programmes Extra Duration: hs/mins Energy Consumption: kWh Water Consumption: litres Switch off the device All done . . . Open the door when the buzzer has sounded 5 times (programme stop). "Ready" is briefly displayed, the appliance automatically switches off after 5 seconds. Eco Normal Plus 2:15 0, 65 19 2:20 1, 05 12 2:20 1, 05 14 2:20 1, 05 15 Maintenance and care Strainers . . . Check, if required, clean Rotate filter cylinder, remove filter system . . . For perfect rinsing results . . . rinse under flowing water . . . Screw in filter system NOTE MARK! Cleaning the waste-water pump * * With some models ­ Ladle out water and remove filters ­ Unscrew cover (Torx T20) ­ Check area of fan impeller for foreign objects ­ Screw in cover and insert filters Spray arms . . . Remove blockages/deposits Pull lower arm upwards . . . Unscrew upper arm . . . Clean spray nozzles under flowing water (perhaps with toothpick) . . . Insert lower arm . . . Screw in upper arm Eliminating minor faults yourself . . . Fault Possible Cause . . . Self-help pays! Remedy Fault Possible Cause Remedy Display in wrong language Language changed Switch off and on the device. Press the button M/OK repeatedly until the display shows the language selection. Select the language using ­/+, and store the selection using M/OK. Dishes not clean Sand or grainy residues on dishes Utensils are situated too close to each other or on top of each other Too little cleaning product Unsuitable programme selected Spray nozzles blocked Filters dirty, not installed securely Spray arms blocked Spread out the utensils, avoid contact between the utensils. Follow manufacturer's specifications (detergent). Arrange the utensils so that the spray arms can rotate freely. Residual water in the device Programme does not start, does not run on Waste-water pump blocked Programme has not been started Door was opened before end of programme Clean waste-water pump (see above) If necessary, start programmes. Wait for programme stop (buzzer sounding 5 times). Stains and streaks Rinse aid dosage too high / too low Streaks: Reduce dosage. Water or limescale stains: Increase dosage. Device does not work/stops Supply fitting not open Supply hose kinked Supply fitting jammed or calcified Open supply fitting. [. . . ] ­ Close the door and wait until the buzzer is emitted 5 times. ­ Restart the programme or switch off the appliance. Arranging utensils correctly . . . Arrange dishwasher-proof utensils (having removed any ash, wax, grease or ink. Coarsely remove sticky labels, large remnants of jam, milk products or food) according to the operating instructions and check that the spray arms can rotate freely. [. . . ]