User manual NEFF T69S86N0AU

[. . . ] T69S86N0AU This cooktop is for use with Natural Gas and Universal LPG Neff GmbH Carl-Wery-Stra ße 34 81739 München Cod. 9000504214 A AS 4551:2008 GMK 10010 Notes: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When being repaired, the appliance must always be disconnected from the mains supply; if required, notify our customer service. Converting the cooktop from Nat. Gas to Propane Gas To change injectors All work involved in installation, setting and adaptation to a different gas type must be carried out by authorised personnel from our Service Centre and must comply with current regulations and the conditions laid down by the local gas company. Request change-over injectors from our customer service deparment (refer injector chart below for sizes). Natural Gas Burner Hourly Gas Consumption (MJ) Injector mark (mm) Propane Gas Hourly Gas Consumption (MJ) Injector mark (mm) Small Medium Large wok (inner) wok (outer) distanze "Z'' 4, 80 8, 10 11, 60 22, 00 11 97 130 157 65 215 3, 50 6, 00 8, 50 20 12 53 70 83 47 115 12 Before conversion the cooktop must be disconnected from the electricity and gas valves must be turned to the OFF position. Changing the nozzles of the large, medium and small burners on the cooktop - Remove the pan supports, burner covers and diffusers. Fig. 7 - Change the nozzles using the spanner provided by our Service Centre (code 424699), taking special care to ensure that the nozzle does not fall when it is removed from the burner or when fitted. Ensure that it is completely tightened in order to guarantee the seal. Primary air adjustment is not necessary with these burners. Note: it is not necessary to adjust the primary air control on these burners. Fig. 8 Changing doubleflame burner tips The glass panel and frame are fixed to the rest of the cooktop using a clip mounting system. The following steps must be taken to remove the glass panel and frame: - Remove all the burner covers and pan supports. - Release the front clip fixing the appliance to the kitchen unit by removing the screw. - Loosen the screws on the burners, Fig. 9c, and remove the control knobs from their respective housings. Fig. 9c Use the disassembly lever 483196 available from our Sere Centre. To release the front clips, apply the lever in the area shown in figures 10 according to the cookop model. Fig. 10 13 Never use the lever on glass edges which have no trim or frame!- To release the rear clips, carefully raise the entire glass panel and frame, as in Fig. 10a. Fig. 10a Changing the outer flame nozzle (Fig. 11) - Loosen the clamp screw to release the bushing by moving it backwards to access the main nozzle easily. - Remove the outer flame nozzle by turning it towards the left. - Adjust the distance of the airflow adjusting bushing L2 according to the value -Z-. 11 14 Changing the inner flame nozzle (fig. 12) - Unscrew the part M3 from the threaded part M2; to do this, hold the threaded part in the opposite direction. [. . . ] There may be a leak in the gas cylinder coupling. The control knob was not held down for long enough. The grooves on the diffuser are dirty. Ensure the components are correctly positioned. Change the gas cylinder. The flow of gas does not appear normal or no gas comes out. The kitchen smells of gas. [. . . ]