User manual NERO COVERDESIGNER 2 REV 1

[. . . ] Nero CoverDesigner Manual Nero AG Copyright and Trademark Information The Nero CoverDesigner manual and all its contents are protected by copyright and are the property of Nero AG. This manual contains materials which are protected by internationally recognized copyright laws. This manual may not - in whole or in part - be copied, transmitted, or otherwise reproduced without the express written permission of Nero AG. All trade names and trademarks are the property of their respective owners. Nero rejects any claims that transcend the clauses of the guarantee rights. Nero AG does not undertake any liability for the correctness of the content of the Nero CoverDesigner manual. [. . . ] Specifies the text for the Custom Text field type. Specifies the text that appears in front of the selected field type. Specifies the text that appears after the selected field type. The field type that you select in the Field Type selection list is applied to the inserted field even if you assigned a different field type beforehand. Page 40 Geometry window 13 Geometry window The position, size, and rotation of an object are determined in the Geometry window. To open the window, select Object > Geometry from the menu. Fig. 10: Geometry window The window contains the following fields: Position Area X Y Size Area Width Height Rotation Area Angle Specifies the angle of rotation. Specifies the width of the object in mm. Specifies the height of the object in mm. Specifies the X coordinate of the top left point of the frame. Specifies the Y coordinate of the top left point of the frame. Page 41 Geometry window 13. 1 Geometry window for bent objects For bent objects, the position of the center and the position of the object in terms of the center are specified in the Geometry window. To open the window, select Object > Geometry from the menu. Fig. 11: Geometry window for bent objects The window contains the following fields: Center Area X Y Rotation Area Specifies the position of the text in relation to the center point. The starting point of the text is the left edge of the first character. The division into degrees is the one commonly used in mathematics: 0 degrees is on the right at the height of the midpoint and the units progress in a counterclockwise direction. Selecting 180 degress, for example, bends the text in a semicircle. Specifies the X coordinate of the center point (which the object is rotated around). Specifies the Y coordinate of the center point (which the object is rotated around). Start Arc Page 42 Align Elements window 14 Align Elements window The Align Elements window aligns objects relative to the page, i. e. , the editable drawing area, or another object. To open the window, select Object > Align from the menu. This feature is not available for bent objects. Fig. 12: Align Elements window The window contains the following check boxes and option buttons: Specifies the horizontal alignment. There are three option buttons: Horizontal Alignment Left: Aligns the object along the left edge. Right: Aligns the object along the right edge. There are three option buttons: Vertical Alignment Top: Aligns the object along the top edge. Bottom: Aligns the object along the bottom edge. [. . . ] 31, 37 Swirl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 P Paper profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Paper stock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Assigning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Specifying default settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66, 67 T Template Creating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 52 Modifying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]