User manual NETGEAR ANT24BDC PRODUCT BROCHURE

[. . . ] All NETGEAR antennas are FCC-approved to work with the following NETGEAR models: FVM318, FWG114P ME103 and WG302. , 18 dBi Patch Panel Directional Antenna The ANT24D18 indoor/outdoor directional* antenna provides a 3-in-1 solution for mixed applications in combination with an 802. 11b or 802. 11g access point or wireless router. One, it delivers extended access point range in a single floor environment ideally positioned in the corner of a building. [. . . ] Includes mounting brackets, cable sold separately. *** ** Omni-directional: Radiates radio-frequency energy equally in all directions for widespread, all-points deployment. ***NETGEAR recommends use of antenna cable up to 5 m long with the ANT24O5 antenna. 500 mW Power Booster**** The 500-milliwatt bi-directional power booster increases the transmission signal from an average 50 mW to 500 mW and amplifies the signal by 10 dB (10 times) in receive mode. It is used to enable a single access point device to cover a larger area. Consisting of a bi-directional amplifier, 500 mW (+27 dBm) in transmit mode for +5 to +15 dBm input, it provides 10 dB gain in receive mode. It can also be used to fully compensate for the loss of long antenna cables without any reduction of performance, and permits one to position an antenna at a greater distance from a wireless node. Used in conjunction with a high gain antenna, such as the 18 dBi ANT24D18, it can provide very high outdoor range ­ up to 120 km or about 74 miles. Easy to install, no configuration required; includes ceiling/wall mount bracket, cable sold separately. **** NETGEAR has approved this product for use in the United States only. As per FCC regulations, the ANT24BNA booster is sold as part of a transmission system which includes the ME103 802. 11b ProSafe Wireless Access Point and the NETGEAR 3m cable (ACC-10314-02). This product may only be ordered as part of a bundle p/n: ME103BDL1NA. Use of the ANT24BNA with any other products is strictly prohibited by FCC regulations. Netgear expressly disclaims the implied warranty of merchantability and fitness for a particular purpose for any damage caused by misuse of the ANT24BNA. Power Injector for the 500 mW Booster An optional accessory for the 500 mW booster, the ANT24BDC power injector provides power through the antenna cable to the booster. Use this device when the booster is not located near a power outlet. Installed between the access point and the booster, this device injects up to 12 volts and 2 amps to the booster. The antenna cable from the access point to the injector can be up to 3 m in length. The cable between the injector and the booster can be up to 10 m long to achieve maximum performance benefits. Low-loss Antenna Cables These 1. 5 m, 3 m, 5 m, and 10 m antenna cables offer low loss at 2. 4 GHz and added flexibility for setting up access points at a greater distance from a power source. They come with reverse SMA connectors and provide a standard connection optimized for use with NETGEAR`s line of WLAN antennas, and Booster/Power Injector products (range can be drastically reduced if longer or higher loss cables than these are used. ) 1 8 d B i Pa t c h Pa n e l D i r e c t i o n a l A n t e n n a - A N T 2 4 D 1 8 Technical Specifications Description: Typical Application: Maximum Outdoor Range1: Frequency Range: Gain2: Beam Width: Dimensions: Weight: Package Contents: 18 dBi Patch Panel Directional Antenna with reverse N female jack and reverse N to reverse SMA adapter Indoor/outdoor long range point-to-point connections 15. 8 km (~9. 8 miles) 2. 400 ~ 2. 485 MHz 18 dBi Horizontal 60° Vertical 30° 262. 8 x 262. 8 x 40 mm (10. 35 x 10. 35 x 1. 58 in) 1520 g/3. 35 lbs. [. . . ] NETGEAR®, the Netgear Logo, ProSafe, Everybody's connecting and Auto Uplink are trademarks or registered trademarks of Netgear, Inc. in the United States and/or other countries. Other brand and product names are trademarks or registered trademarks of their respective holders. [. . . ]