User manual NETGEAR DS100 INSTALLATION GUIDE

[. . . ] A link is successfully established between the hub and the PC. No data link is established and/or the cable is not connected, is defective, or is the wrong type. Amber Amber On On Data collision is occurring on the 10 Mbps network segment (some collisions are normal). Data collision is occurring on the 100 Mbps network segment (some collisions are normal). [. . . ] No nearby heat sources such as direct sunlight, warm air exhausts, or heaters. 90% maximum relative humidity, noncondensing. Minimum 2 inches (5. 08 cm) on all sides for cooling. Adequate airflow in room or wiring closet. At least 6 feet (1. 83 m) to nearest source of electromagnetic noise (such as photocopy machine or arc welder). Minimum 12 inches (19. 68 cm) front and back for service access and maintenance. Front and back clearance for cables and wiring hardware such as punchdown blocks. Adequate power source within 6 feet (1. 83 m). Humidity Ventilation Operating conditions Service access Power Wiring hardware Wiring hardware, such as punchdown blocks or patch panels, complete before installing the hub. Install the Hub Install the Hub on a Flat Surface If installing the hub on a flat surface such as a tabletop, make sure the bottom of the chassis is clean and dry. To install the hub on a flat surface: 1. Set the hub on a table or shelf so that it has at least 2 inches (5 cm) of space on all sides. Connect the power cord(s) first to the power entry receptacle on the hub rear panel and then to the wall. Install the Hub on a Wall If installing the hub on a wall, make sure you have a Phillips screwdriver. Set the mounting screws and anchors (supplied with the wall mount hardware) in the wall. Using the slots on the bottom of the hub, hang the hub on the wall. Connect the power cord(s) first to the power entry receptacle on the hub rear panel and then to the wall. Model DS104/DS106/DS108/DS116 Dual Speed Hub Installation Guide Connect a PC to the Hub Power Collision 10M Link Activity 100M Link Activity Norma l/Uplin k 9097FA Set Normal/Uplink Push Button The Normal/Uplink push button on the front panel of the hub allows you to select the Uplink (MDI) or Normal (MDI-X) position for port 4 on the Model DS104 hub, port 6 on the Model DS106 hub, port 8 on the Model DS108 hub, and port 16 on the Model DS116 hub. All other ports are wired Normal for direct connection to PCs. Select Normal if connecting a PC, server, or router to the port. Select Uplink if connecting a hub or switch. The Normal/Uplink push button eliminates the need to use a crossover cable. Caution: 100 Mbps operation requires the use of Category 5 UTP wiring with 100 Mbps certified connectors. NETGEAR highly recommends using Category 5 cable so your network can operate at either 10 or 100 Mbps. Model DS104/DS106/DS108/DS116 Dual Speed Hub Installation Guide Connect Hubs at 10/100 Mbps 10 or 100 Mbps Transmission with the Hub Two Model DS104 hubs, two Model DS106 hubs, two Model DS108 hubs, two Model DS116 hubs, or a combination of DS100 Series hubs can be daisychained together at 100 Mbps to support a growing number of PCs. For larger networks, use a 10/100 Mbps switch such as the NETGEAR Model FS104 switch, as shown in the illustration below. Switched network with Model DS104, Model DS108, and Model DS116 hubs Server Model FS104 10/100 Mbps switch Model DS104 hub DUAL SPEED Model DS108 hub DUAL SPEED HUB DS104 100 Mbps 100M 10M On - Link Blinking = Receive Normal/Uplink 1 Pow Col 10 20 >40 10 Mbps Utilization% 1 2 3 4 PCs Model DS116 hub DUAL SPEED HUB DS116 Power PCs Auto 10/100 Mbps DUAL SPEED 10M Link Activity 100M Link Activity Normal/Uplink Collision 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PCs 9093FA The following illustration shows a two-hub daisy-chain configuration. [. . . ] Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right to test the series for compliance with the regulations. Voluntary Control Council for Interference (VCCI) Statement This equipment is in the first category (information equipment to be used in commercial and/or industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing Equipment and Electronic Office Machines that are aimed at preventing radio interference in commercial and/ or industrial areas. Consequently, when this equipment is used in a residential area or in an adjacent area thereto, radio interference may be caused to equipment such as radios and TV receivers. Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy. [. . . ]