User manual NETGEAR EA101C INSTALLATION GUIDE

[. . . ] Follow the illustration below to connect the network cables. PC with network card installed Power adapter PC with USB port Hub USB connector Model EA101 USB Ethernet Adapter Category 5 10/100 Mbps UTP cables* *Use the cables provided or any Category 5 UTP cable. Maximum length = 100 meters (300 feet) 9310FA Note: One of the ports on NETGEAR hubs is switchable between Normal (MDI-X) and Uplink (MDI) with a Normal/Uplink push button. If you are using this switchable port on a NETGEAR hub to connect to a PC, a network card, or to the Model EA101 USB Ethernet adapter, make sure the Normal/Uplink push button is set to Normal. Model EA101 USB Ethernet Adapter Installation Guide Install the Network Driver This guide provides you with instructions for installing the Windows network driver. The steps given in these instructions are for users of Windows 98. [. . . ] OK Click on "OK. " 7. Copying Files. . . The file 'EA101ND4. SYS' on NETGEAR EA101 USB Ethernet Adapter Drivers Disk could not be found. Insert NETGEAR EA101 USB Ethernet Adapter Drivers Disk in the selected drive and click OK. OK Cancel Skip File Copy files from: A:\ Details. . . Browse. . . Make sure that the location and the correct driver are displayed (for example, A:\). Click on "OK. " Note: If you copied the Windows 98 CD-ROM to your hard drive, the next two windows may not appear. 8. Insert Disk Please insert the the disk labeled 'Windows 98 CD-ROM' and then click OK. OK Click on "OK. " Model EA101 USB Ethernet Adapter Installation Guide 9. Copying Files. . . The file 'choosusr. dll' on Windows 98 CD-ROM could not be found. Insert Windows 98 CD-ROM into the drive selected below, and click OK. OK Cancel Skip File Copy files from: D:\WIN98 Details. . . Browse. . . Insert the Windows 98 CD-ROM. Make sure the designated path to the Windows 98 CD-ROM is displayed in the "copy files from" prompt line (for example, D:\WIN98). Click on "OK. " 10. Update Device Driver Wizard NETGEAR EA101 USB Ethernet Adapter Windows has finished installing the software that your new hardware device requires. < Back Finish Cancel Click on "Finish. " 11. Network ? To finish setting up your new hardware, you must restart your computer. Do you want to resatrt your computer now?Yes No Remove the NETGEAR EA101 Drivers and Diagnostics Disk and the Windows 98 CD-ROM. Click on "Yes" to restart your computer. You must restart your computer to complete the installation of the driver. Proceed to "Verify Installation. " Model EA101 USB Ethernet Adapter Installation Guide Verify Installation 1. Double-click on "My Computer" on your desktop, double-click on "Control Panel, " and then double-click on "System. " 2. Click on "Device Manager. " Model EA101 USB Ethernet Adapter Installation Guide 3. Double-click on "Network adapters" and then double-click on "NETGEAR EA101 USB Ethernet Adapter" to open the "Properties" window that displays a message regarding the status of the device. If there is a problem with the driver installation, an exclamation point appears next to "NETGEAR EA101 USB Ethernet Adapter. " 4. Continue to click on "OK" or click on the "X" in the right-hand corner to close any open windows and return to the Windows 98 desktop. Model EA101 USB Ethernet Adapter Installation Guide Technical Specifications Model FA510 Network Card Standards Compatibility Interface Options IRQ Options Power Consumption Physical Specifications Dimensions Weight Environmental Specifications Operating temperature Operating humidity Agency Compliance 0° to 45° C 10% to 90% noncondensing CE mark, commercial FCC, Part 15, Class B EN 55 022 (CISPR 22), Class B Canada ICES-003, Class B VCCI Class B 0. 14 lb (63 g) Microsoft Windows 98 compatible IEEE 802. 3i, 10BASE-T Ethernet RJ-45 connector Assigned by Plug-and-Play system 2. 0 W Model EA101 USB Ethernet Adapter Installation Guide © 2000 by NETGEAR, Inc. Trademarks NEGEARTM is a trademark of NETGEAR, Inc. Windows®is a registered trademark of Microsoft Corporation. Other brand and product names are trademarks or registered trademarks of their respective holders. [. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna, (2) Increase the separation between the equipment and receiver, (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected, (4) Consult the dealer or an experienced radio/TV technician for help. EN 55 022 Statement This is to certify that the Model EA101 USB Ethernet Adapter is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. [. . . ]