User manual NETGEAR GS104 Installation Guide

[. . . ] You'll find technical support information at: http://www. NETGEAR. com/ through the customer service area. If you want to contact technical support by telephone, see the support information card for the correct telephone number for your country. NETGEAR, Inc. NETGEAR and Auto Uplink are trademarks or registered trademarks of NETGEAR, Inc. in the United States and/or other countries. [. . . ] Find a flat horizontal surface -- such as a table, desk or shelf. The switch comes with wall-mounting screws. You're welcome to use the screws if you want to hang the switch in an open space on a wall. Make sure the selected location is: Not in direct sunlight or near a heater or heating vent. There should be at least 2 inches (5 cm) of clear space on all sides of the switch. Well ventilated (especially if it is in a closet). Also, you'll need one Category 5 (Cat 5) Ethernet cable with RJ-45 connectors for each device you want to connect to the switch. Each Ethernet cable must be less than 328 feet (100 meters). 3 Install the Switch and Connect the Other Devices Apple G4 PC with GA302T Adapter 10/100/1000 Mbps Gigabit Switch GS104 Server with GA622T Adapter DSL modem LOCAL 10/100M Gigabit Ethernet 1000M 100M 8 7 6 5 4 3 2 1 INTERNET 12VDC 1. 2A On=10M, Blink=ACT 1 Power 2 3 4 Auto Uplink OFF ON Green=FDX, Yellow=COL 1 2 3 4 GS104 4-Port 10/100/1000 Mbps Gigabit Ethernet Switch FVS318 Cable/DSL ProSafe VPN Firewall 1. 3. Place the switch on a flat surface or hook onto the screws. For each device, insert one end of an Ethernet cable into the port in the device and insert the other end into one of the Ethernet ports on the switch. Connect the power adapter's cord into the back of the switch and then plug the adapter into a power source (such as a wall socket or power strip). The Power light should light up. Power ACT, FDX, COL LED 10/100/1000 Mbps Gigabit Switch GS104 1000M 100M LED LED Gigabit Ethernet 1000M 100M On=10M, Blink=ACT The corresponding Link LED for each connected and Model GS104 4-Port 10/100/1000 Mbps Gigabit Ethernet Switch powered device should light and flash when activity occurs. If the connection is 1, 000 Mbps or 100 Mbps, the LED in the RJ-45 jack will light up. If the connection is 10 Mbps, the 10M LED on the left side of the front panel wll light up. 1 2 3 4 Auto Uplink Power Green=FDX, Yellow=COL 1 2 3 4 Note: If any light doesn't operate as indicated, go to the Troubleshooting section. Troubleshooting The Power light is not lit The switch has no power. · Make sure the power cord is properly connected to the switch. · Power Make sure the power adapter is properly connected to a functioning power outlet. If it's in a power strip, make sure the power strip is turned on. If the socket is controlled by a light switch, make sure the switch is in the on position. Make sure you are using the NETGEAR power adapter supplied with your switch. · The Port number light is not lit for a connected device or stays on continuously There's a hardware connection problem. · Make sure the cable connectors are securely plugged in at the switch and the device. · · · Make sure the connected device is turned on. [. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ]