User manual NETGEAR GS608

[. . . ] Each port on the GS605/GS608 switch automatically configures itself correctly when you plug in a device's cable. Installation guide, Warranty/ Support information card Vertical stand Power adapter When you open the box, verify that you received everything. The package includes: · · · · · 5/8-port Gigabit Ethernet Switch GS605/GS608 Power adapter Vertical stand Installation guide Warranty/Support information card Installation Overview Estimated Time: 5­10 minutes 1. Install the switch and connect the other devices. 2 · · Prepare to Install the Switch Decide where you want to place the switch. [. . . ] Make sure the selected location is: Not in direct sunlight or near a heater or heating vent. There should be at least 2 inches (5 cm) of clear space on all sides of the switch. 1 2 · Well ventilated (especially if it is in a closet). Note: Neither the GS605 nor GS608 are designed to be stacked on top of other GS605 or GS608 switches. If you need several units in one location, use the vertical stand to position several units near each other. Also, you'll need one Enhanced Category 5 (Cat 5e) Ethernet cable with RJ-45 connectors for each device you want to connect to the switch. Each Ethernet cable must be less than 328 feet (100 meters). Note: If you have more than 5 or 8 devices to connect to this switch, you must connect them to a hub or other switch and then connect that hub or switch to this switch. See the note about placing several switches near each other in section 2. Connect the power adapter's cord into the back of the switch and then plug the adapter into a power source (such as a wall socket or power strip). The corresponding port number for each connected and powered device should light when link (connection), and flash when activity occurs. 3 Install the Switch and Connect the Other Devices Troubleshooting The Power light is not lit The switch has no power. · · Make sure the power cord is properly connected to the switch. · This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Performance Specifications Frame Filter Rate: Frame Forward Rate: Network Latency: (using 64-byte packets) Address Database Size: Addressing: Packet Buffer Memory: 14, 800 frames/sec max for 10M port/148, 800 frames/sec max for 100M port/1, 488, 000 frames/sec max for 1000M port 14, 800 frames/sec max for 10M port / 148, 800 frames/sec max for 100M port/1, 488, 000 frames/sec max for 1000M port 1000 Mbps to 1000 Mbps: 20 µs max 4000 MAC addresses 48-bit MAC address 1 Mb EN 55 022 Declaration of Conformance This is to certify that the NETGEAR Model GS605/608 Gigabit Ethernet Switch is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. [. . . ] Conformity is declared by the application of EN 55 022 Class A (CISPR 22). Canadian Department of Communications Radio Interference Regulations This digital apparatus (NETGEAR Model GS605/608 Gigabit Ethernet Switch) does not exceed the Class A limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications Règlement sur le brouillage radioélectrique du ministère des Communications Cet appareil numérique (NETGEAR Model GS605/608 Gigabit Ethernet Switch) respecte les limites de bruits radioélectriques visant les appareils numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique du ministère des Communications du Canada. 5 6 Technical Support PLEASE REFER TO THE SUPPORT INFORMATION CARD THAT SHIPPED WITH YOUR PRODUCT. By registering your product at www. NETGEAR. com/register, we can provide you with faster expert technical support and timely notices of product and software upgrades. ©2004 NETGEAR, Inc. NETGEAR, the Netgear logo, Auto Uplink, ProSafe and Everybody's connecting are trademarks or registered trademarks of Netgear, Inc. [. . . ]