User manual NETGEAR JGS524 Installation Guide

[. . . ] LEDs Installation Guide Gigabit Ethernet Switch Series JGS500 Applications Desktop Switching Color Green Label PWR (Power) Activity Description On Off Power is supplied to the Switch Power is disconnected The port is operating in 1000 Mbps mode The port is operating in 100 Mbps mode The port is operating in 10 Mbps mode Valid link on the port Packet transmission or receiving on the port Start Here The NETGEAR JGS516 16-port Gigabit Ethernet Switch and JGS524 24-port Gigabit Ethernet Switch provide you with a low-cost, high performance network solution, designed to support power workgroups operating at speeds from 10 megabits per second (Mbps) to 1000 Mbps. Gigabit Ethernet switches provide 10 times the bandwidth that Fast Ethernet switches do, boosting the speed at which files, voice, video, imaging, or other applications move across your network. [. . . ] This feature also eliminates the need to worry about crossover cables, as Auto Uplink will accommodate either type of cable to make the right connection. JGS524 Speed PWR 9 10 11 12 13 14 15 16 Link/Act 9 10 11 12 13 14 15 16 Auto Uplink JGS516 16-port 10/100/1000 Mbps Gigabit Ethernet Switch 10/100/1000 Mbps ports PORT 24 10/100/1000Mbps Gigabit Ethernet Switch Green=1000M, Yellow=100M 1 2 3 4 5 6 7 8 9 10 11 12 MODEL Speed 1 2 3 4 5 6 7 8 9 10 11 12 Link/Act Speed PWR 13 14 15 16 17 18 19 20 21 22 23 24 Link/Act 13 14 15 16 17 18 19 20 21 22 23 24 Auto Uplink Note: Auto Uplink will compensate for setting uplink connections, and crossover or straight-through cables. Using Auto Uplink to create multiple paths between any two network devices will disable your network. JGS524 24-port 10/100/1000 Mbps Gigabit Ethernet Switch JGS516 Standards Compatibility JGS524 Install the Switch To install your switch on a flat surface, you do not need any special tools. Be sure the switch is positioned with at least 2 inches of space on all sides for ventilation. To install the switch in a rack, first attach the mounting brackets to the side of the switch. Insert the screws provided in the rack mount kit through each bracket mounting hole in the switch. Tighten the screws with a #1 Phillips screwdriver to secure each bracket. Align the mounting holes in the brackets with the holes in the rack and insert two pan-head screws with nylon washers through each bracket and into the rack. Tighten the screws with a #2 Phillips screwdriver to secure the switch in the rack. Technical Support PLEASE REFER TO THE SUPPORT INFORMATION CARD THAT SHIPPED WITH YOUR PRODUCT. By registering your product at www. NETGEAR. com/register, we can provide you with faster expert technical support and timely notices of product and software upgrades. IEEE 802. 3i 10BASE-T Ethernet, IEEE 802. 3u 100BASE-TX Fast Ethernet, IEEE 802. 3ab 1000BAS-T Gigabit Ethernet, IEEE 802. 3x Flow Control Compatible with major network software, including Windows, NetWare and Linux RJ-45 connector for 10BASE-T, 100BASE-TX, or 1000BASE-T Ethernet interfaces 25 W max 330x207x43mm / 13x8. 15x1. 70 inch 2kg/4. 4 lbs 40 W max 330x207x43mm / 13x8. 15x1. 70 inch 2kg/4. 4 lbs Network Interface Power Dimensions Connect the Devices To connect devices to the switch: 1. Connect the devices to the 10/100/1000 Mbps ports on the switch, using Category 5 UTP cable and RJ-45 plug. [. . . ] Other brand and product names are trademarks or registered trademarks of their respective holders. Information is subject to change without notice. [. . . ]