User manual NETGEAR SPH200D

[. . . ] Cordless Internet Phone with SkypeTM Model SPH200D User Manual NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA 202-10216-01 November 2006 © 2006 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR , the NETGEAR logo, and Auto Uplink are trademarks or registered trademarks of NETGEAR, Inc. Skype, SkypeIn, SkyeOut, SkypeMe, Skype Voicemail, the Skype logo, and the S logo are trademarks of Skype Limited. [. . . ] You can choose to check for updates manually, or to have your phone notify you when an update is available. Note: Some updates are optional and can be downloaded at anytime. Note that some updates are required and must be accepted immediately in older to continue using the phone. To update Skype software, press Menu>Settings>Advanced>SW Update. You can choose: · · SW Update. If an update is available, follow the onscreen instructions Auto Update. Set the phone to notify you of new Skype software updates. This takes less time than checking for new updates manually. Note: With Auto Update, your phone displays a message when there is a new update. You will be able to choose to update the software right away or to have your phone remind you again at a later time. Skype Calling v1. 0, November 2006 3-11 Cordless Internet Phone with Skype Model SPH200D User Manual 3-12 v1. 0, November 2006 Skype Calling Chapter 4 Landline Calling You can use your phone to make Skype calls over the Internet or to make landline calls with your regular phone line. Note: Your phone stores the outgoing, incoming, and missed calls. For information about calling from the Call History, see "Personalizing Your Handset Display" in Chapter 6. Making a Landline Call There are two ways that you can make a landline call. You can use direct dialing, or select the landline option. Direct Dialing To use direct dialling, follow these steps: 1. Wait for the call to connect, ring, and be answered. Press End to end the call. 4-1 v1. 0, November 2006 Cordless Internet Phone with Skype Model SPH200D User Manual Selecting the Landline Option To select the landline option, follow these steps: 1. Wait for the call to connect, ring, and be answered. Press End to end the call. Figure 4-1 Redialing the Last Number Press twice within one second. The last number that you called is dialed out using the same line as before. The last number that you called using the landline will be dialed out. Making a Second Landline Call During a Call Note: Second call service only applies to calls using the landline. Toggling between calls may not be available in all countries. Consult and subscribe from your landline service provider. Press . The current caller is put on hold. [. . . ] Default Factory Settings Item System Setting Network Setting Default Setting PIN Code: 0000 Country: Empty DHCP: Enabled Network Proxy Option: Auto Network Proxy Host: Auto Network Proxy Port: Auto Proxy Authentication: Disabled Authentication User Name: Empty Authentication Password: Empty Application Port: Skype default Alternate Application Ports: Skype defaults Technical Specifications Technical Specifications Antenna Frequency Emissions Interface Weight with battery Dimensions (H x W X D) Operating temperature Internal · DECT (1. 8 GHz) · UPCS (1. 9 GHz) North America FCC, CE · Ethernet (RJ-45) · PSTN (RJ-11) · base station: 235g · handset: 130g with batteries · base station: 137 x 126. 5 x 70 mm · handset: 141. 5 x 46 x 26 mm 32°­104°F (0°­40°C) A-2 Default Factory Settings and Technical Specifications v1. 0, November 2006 Cordless Internet Phone with Skype Model SPH200D User Manual Power and Safety Power Requirements To install the Cordless Internet Phone with Skype Model SPH200D, you need the following: · North America: -- 120 volts, single-phase AC. -- This product requires an electrical supply of 120 volts, single-phase alternating current, excluding IT installations defined in standard UL 60950-1. · Europe: -- 220-230 volts, single-phase AC. -- This product requires an electrical supply of 220-230 volts, single-phase alternating current, excluding IT installations defined in standard EN 60950-1. [. . . ]