User manual NEXT BASE SDV485-A

[. . . ] M ODEL NO. SDV485-A OPERATING INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS ENG 01 Read these instructions. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (Including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] Note that the remote control unit may not work if there are obstacles between the remote sensor and itself. Do not expose the remote sensor to strong light. Use the remote control unit within the specified operating range. REPLACING THE BATTERY 1 Insert your finger nails into A and B on the diagram below, press A according to the direction, then pull out the battery holder. 2 Remove the old battery, then insert the new battery into the battery holder with the + side facing upwards. B A Lithium Battery (CR2025) NOTE: To prevent leakage of fluid fro m the lithium battery, remove the ba ttery when not using the re mote control unit for long periods of time (One mont h or more). If the battery leaks fluid, carefull y wipe it out of th e battery case , then change to a new lithium battery. Caution: Th e battery may present a risk of fire if mistrea ted. Do n ot rec harge, d isassem ble, or heat it abo ve 100 C . Dis pose of used bat tery prop erly, kee p away from chil dren and do not dispose of i n fire. 3 Fit the battery holder back to its place. MOBILE ENTERTAINMENT AUDIO / VIDEO CONNECTIONS ENG 19 CONNECTING THE PLAYER TO A TV SET Yellow Black Yellow White Red MOBILE ENTERTAINMENT 20 ENG AUDIO / VIDEO CONNECTIONS CONNECTING THE ADAPTER TO THE DC IN 12V SOCKET USING THE EARPHONE Set the volume control to minimum sound level. Connect the earphone plug to the player's " " jack. Adjust the volume control to the preferred sound level. MOBILE ENTERTAINMENT CONNECTING THE PLAYER TO OTHER DEVICES ENG 21 CONNECTING TOA DOLBY DIGITAL / MPEG DECODER OR AN AMPLIFIER WITH A BUILT-IN DECODER With thi s player, you can enjoy po werful D olby Dig ital or M PEG sou nd. Output the digital s ignals from the p layer's d igital output to a decoder or ampli fier with built-in decoder. Main unit right panel See details of connections to the TV. Front speaker (Left) Optical digital cable (Not included) Front speaker Subwoofer (Right) Center speaker (Left) Sur round spe aker (Right) Signal flow Surro und speaker Hint: For a compatible decoder or a mplifier, 5 sp eakers (Fro nt left /right, center and s urround left/ right) and a subwo ofer a re req uired t o enjo y Dolb y Digi tal channel sound. MOBILE ENTERTAINMENT 22 ENG CONNECTING THE PLAYER TO OTHER DEVICES CONNECTING TO A DIGITAL AMPLIFIER THAT IS NOT DOLBY DIGITAL / MPEG COMPATIBLE Output the digit al signal s from th e player 's digita l output t o a digital amplif ier that is not D olby/MP EG com patible. For instr uctions o f audio settings, refer to AUDIO OUT of AUDIO SETUP. Main unit right panel Optical digital cable (Not included) See details of connections to TV. To digital audio input jack Signal flow Notes Carefu lly check the pla yer s dig ital output settings before c onnecting the pla yer to an amplifier equipped with a digital audio inpu t jack which is not D olby Digital / MP EG compa tible. Do not play DVDs when the audio settings are not correct. Or it may cause strong noise and damage your speakers. MOBILE ENTERTAINMENT CONNECTING THE PLAYER TO OTHER DEVICES ENG 23 CONNECTING TO ACTIVE SPEAKER SYSTEMS Main unit right side Black Yellow AV cable To Video Input jack To audio input jacks Yellow Active speaker systems MOBILE ENTERTAINMENT 24 ENG BASIC OPERATIONS 1 Connect the AC/DC adapter to a socket. 2 Connect the DC output plug of the 2 adapter to the DC input jack on the main unit. 3 Switch the POWER button to ON position. 3 The included AC/DC adapter is compatible with voltage from 100V to 240 V, you can use it on trips overseas. Power Note that you need a converter plug (Available in stores) suited for the region in which you are travelling. When the power is on, switch the power button to OFF position. Unplug the power cord from the power outlet. Disconnect the AC/DC adapter from the player's DC input jack. MOBILE ENTERTAINMENT BASIC OPERATIONS (IN DVD STATE) ENG 25 LOADING 1 Press the OPEN button to open the cover. 2 Place in a disc and press down the disc with your fingers near the center hole. Failure to set it securely could result in damage. Place single-sided DVDs or CDs in with the label (Printed) side facing upwards. For double-sided DVDs, check each side carefully, then place the disc in securely (Until a click is heard). For CDs or one-sided DVDs, you do not have to worry about touching the label (Printed) side of the disc with your fingers. Since two-sided DVDs have signals recorded on both sides, be careful not to scratch them when removing them from the player. 3 Close the disc cover. MOBILE ENTERTAINMENT 26 ENG BASIC OPERATIONS (IN DVD STATE) PLAYBACK 1 Turn on the power of the player. 5 The player will load the disc and play automatically. If not, please press the button. PLAY/PAUSE STOP PLAYBACK 1 Press on the remote control while playing. 2 The player remembers the stopping place. 3 To resume playback from the point where it stopped, just press key. 4 To clear stopping mark, press again at stop status. [. . . ] car stereo) to the corresponding frequency to receive the transmitted audio signal from the player. 9 The transmission range will be within approximately 3 meters. MOBILE ENTERTAINMENT 44 ENG IR TRANSMITTER IR TRANSMITTER 1. Press "ADJUST " button to enter the adjustments of brightness, color, TFT mode, view mode, FM transmitter and IR transmitter. Use the / buttons on the main unit board or remote control to choose IR transmitter, then press enter button. FM ON OFF :ENT FM ON OFF :SEL :EXIT 3. [. . . ]