User manual NIKON CAMERA CONTROL PRO

[. . . ] Camera Control Pro Reference Manual Overview This section describes the structure of this manual, outlines Camera Control Pro's main functions, and gives the system requirements and installation instructions. Using Camera Control Pro This section describes how to use Camera Control Pro. Appendices This section lists preferences and describes how to uninstall the software. Important Information on the Product Key The product key may be found on the CD-ROM case. It is required when installing or upgrading this software and can not be replaced if lost. xxxxx­xxx­xxxx­xxxx­xxxx­xxxx Product key SB6E01(B1) 6MS522B1-- Overview Using Camera Control Pro Appendices Overview Introduction About This Manual System Requirements Windows Macintosh Installing Camera Control Pro Windows Macintosh Getting Started Starting and Exiting Camera Control Pro Getting Help Software Updates 20 26 27 7 8 9 10 15 3 6 Click a page number to view. Return to first page 2 Overview Using Camera Control Pro Appendices Introduction 1/3 This manual has been written to help you take advantage of the many features included in Camera Control Pro. Be sure to read this manual thoroughly, and to keep it handy when using Camera Control Pro. Conventions This manual assumes basic knowledge of cameras and Windows or Finder operations. Refer to the documentation provided with your computer or camera for more information. [. . . ] · Change Factor when Exposure Mode is set to Manual (D2 series/ D200 only): Choose how bracketing is performed in manual exposure mode. · Bracketing Type / Bracketing Step / Bracketing Order / Exposure Mode: Choose the bracketing program, exposure or white balance increment, bracketing order, and exposure mode. Bracketing type and bracketing order are not available with the D50. 8/12 Auto Bracketing D2-series D70 D200 D50 D70S D2 series / D200 D70S/D70/ D50 AF-Area Mode Focus Mode Choose the AF-area mode. If Enable controls on the camera body is checked (D2 series/D200 only), the current AF-area mode will be shown, but changes can only be made using camera controls. The current focus mode setting is displayed. This setting can not be changed from Camera Control Pro. Return to first page 53 Overview Using Camera Control Pro Appendices Camera Controls The Mechanical Tab Lens 9/12 Edit. . . D2-series D200 Main Battery Level Clock Battery Level D1-series Displays the focal length and maximum aper ture of the lens currently attached to the camera. Depending on the lens type, some information may not be displayed. If the lens focal length or maximum aperture have been specified manually, an asterisk will appear next to these values. This button is only available when a nonCPU lens is mounted on the camera. displays the dialog shown at right, where the lens focal length and maximum aperture can be entered. Click OK to copy the values to the camera. Displays the level of the main camera battery. Green indicates that the battery has enough charge for continued operation. Yellow indicates that battery level is low; ready a fully charged spare battery pack. Red indicates that the battery is exhausted, and that no further photographs can be taken until the battery pack has been replaced. You may not be able to control the camera from Camera Control Pro when the battery is exhausted. Replace with a fully charged spare battery pack or use an AC adapter (available separately). Displays the level of the camera clock battery. Should this display turn yellow or red, have the clock battery replaced by an authorized Nikon service representative (a fee is charged for this service). Self-Timer and Remote Modes When a D2-series, D200, D70S, D70, D50, or D100 camera is set to self-timer mode, or when the D70S, D70 or D50 is set to delayed remote or quick-response remote mode, the Mechanical tab will show a shooting mode of Single, and any photographs taken with the Camera Control Pro shoot buttons will be taken in single-frame mode with no shutter-release delay. To take pictures in self-timer or remote mode, use the shutter-release button on the camera. Return to first page 54 Overview Using Camera Control Pro Appendices Camera Controls Continuous Mode D2-series D200 D70S D70 D50 10/12 When a D2-series, D200, D70S, D70, or D50 camera is connected, the amount of memory remaining in the camera memory buffer is displayed at the right edge of the simulated LCD panel. This information is updated at regular intervals, but temporary discrepancies may exist between the display and the actual amount of memory remaining in the buffer. Non-CPU Lenses The following restrictions apply to Camera Control Pro when a non-CPU lens is mounted on the camera (the operations listed can still be performed using the controls on the camera body; see the camera manual for details): D2-series D200 With lens data No lens data D1-series D100 D70S D70 D50 Exposure Mode Can not be adjusted. Mode seCan be selected from Aperture- lected with camera priority auto and Manual. [. . . ] of South Africa ZA Foto Distributors, Head Office Nikon House, 516 Kyalami Boulevard, Kyalami Business Park, Midrand 1685. Tel: +27-(0)11-466-2500 Fax: +27-(0)11-466-3400 Finland FI Nikon Nordic AB Suomen toimisto Ojahaanrinne 4, 01600 VANTAA Tel: +358 9 5660 060 Russia RU Nikon Europe BV, CIS Representative Office Zubarev pereulok, d. 15, k. 1, office 541, 129164 Moscow Tel: +7 (095) 733 91 70 France FR Nikon France S. A. S. 191, Rue du Marché Rollay, 94504 Champigny Sur Marne Cedex Tel: +33-(0)8-25-82-10-10 Spain ES Germany DE Finicon S. A. C/Ciencias, 81 Nave-8, Poligono Pedrosa 08908 L'Hospitalet de Llobregat, Barcelona Tel: +34-(0)93-2649090 Fax: +34-(0)93-3363400 Nikon GmbH Tiefenbroicher Weg 25, 40472 Düsseldorf Tel: +49-(0)900-1225564 Phone line costs (# 0, 24 /min) Sweden SE Nikon Nordic AB Anton Tamms väg 3, 194 22 Upplands Väsby Tel: +46-(0)8-594-109-00 Greece GR D. [. . . ]