User manual NIKON COOLSCAN LS2000

[. . . ] Contents Cautions Safety Precautions If You Notice Anything Abnormal Installation and Storage Overview Parts and Accessories What's in the Box Optional Accessories System Requirements Parts of the LS-2000 Status LED Setup Installation Connecting the Power Cable Connecting the SCSI Cable Setting the SCSI ID Using the Scanner Turning the Scanner On Inserting and Removing Adapters Using the MA-20 SLIDE MOUNT ADAPTER Using the SA-20 STRIP FILM ADAPTER Using the IX240 Film Adapter (IA-20) Using the SF-200 Slide Feeder Turning the Scanner Off 35mm Film Scanner LS-2000 Reference Manual -1- Maintenance Cleaning Storage Transport Troubleshooting Specifications Contents -2- Cautions · The reproduction of this manual in whole or in part is prohibited save in cases in which Nikon's prior permission has been obtained. · The information contained in this manual is subject to change without notice. · Nikon has made every effort to produce a perfect manual, but should you find any mistakes, we would be grateful if you would kindly let us know. The address of Nikon's representative in your area is provided separately. [. . . ] Align each frame in the film with an aperture in the lower holder. Aperture Film strip Holder snaps Lower holder Using the Scanner: Using the MA-20 SLIDE MOUNT ADAPTER - 32 - Step 3--Close the FH-2 Step 5--Insert the FH-2 into the slide adapter Close the FH-2, keeping the ends of the black lower and upper Insert the FH-2 in the film slot of the MA-20, with the "Nikon" holders aligned. Fasten the snap on the FH-2 and fit the ends of logo upwards. The direction of insertion depends on which of the upper and lower holders together. the frames in the apertures of the metal part of the FH-2 is to be scanned (in the illustrations below, the arrows show the direction of insertion). 1 4 The fourth frame will be scanned The first frame will be scanned 2 5 The second frame will be scanned The fifth frame will be scanned Step 4--Choose the frame to be scanned The MA-20 can scan only one frame of film at a time. Slide the black plastic holder to align frame to be scanned with one of the two apertures in the metal part of the FH-2. The sixth frame will be scanned The third frame will be scanned 3 6 - 33 - Using the Scanner: Using the MA-20 SLIDE MOUNT ADAPTER Slide the film holder into the slide adapter until the holder touches the back of the film slot. Do not attempt to force the holder in past the mark. Cautions · If the holder does not slide smoothly into the adapter film slot, remove it from the adapter and try again. · The film holder is for use with the MA-20 only. Do not attempt to use the holder with other adapters. Mark · Before scanning, remove dust from the film with a blower or brush. · Do not use the eject button when removing the holder from the adapter. Slide the holder out by hand. When removing the holder from the adapter, wait until the status LED glows steadily, then slide the holder out by hand. Do not use the eject button. Using the Scanner: Using the MA-20 SLIDE MOUNT ADAPTER - 34 - Using the SA-20 STRIP FILM ADAPTER 35 mm film-strips of from two to six frames in length can be scanned using the strip-film adapter. Insert the adapter into the scanner's adapter slot as shown below, sliding it in until it contacts the back of the slot. Push the adapter until the connector on the rear of the adapter is seated securely in the socket at the back of the slot. A plastic tray is provided with the strip-film adapter to catch film ejected from the scanner. If the scanner has been installed on its side, this tray can be attached to the adapter by inserting the hooks on the back of the tray into the holes provided on the bottom of the adapter and then pulling the tray slightly forward. Using the Scanner: Using the SA-20 STRIP FILM ADAPTER - 35 - Inserting film To scan a film strip, grasp the film gently by the sides and slide the it into the adapter's film slot a short distance. The adapter's feed mechanism will be activated and the film will be fed into the scanner automatically. As is the case with mounted slides, strip film should be inserted with the base up and the emulsion surface down. The film is in the correct orientation if the frame numbers on the film are not reversed. The film's edges should be flat or curled slightly downward. Do not use film which curls upwards or which is curled more than 3 mm, as the film may jam or fail to scan properly. Film for use in the scanner should fit in the gauge on top of the adapter. < 3 mm Film will be ejected from the scanner automatically when the scanner is turned on or when no operation is performed for several minutes. Film can also be ejected using the software provided with your scanner. For details of scanning operations, refer to the User's Guide or software reference manual. Note: Due to varying degrees of curl in strip film, autofocusing may not perform well when scanning the portion of the image close to the front edge of the first frame. [. . . ] ware for the SCSI adapter as described in the manufacturer's manual, follow the steps given in the Fast Track and user's guides to set up your scanner and reinstall the scanner software. Troubleshooting - 52 - Problem: a "no adapter in device" error appears If the software displays a "no adapter in device" error when you attempt to scan, check that there is an adapter in the device and that it is fully inserted in the adapter slot. In the case of the SA-20, the optional IA-20 IX240 adapter, and SF-200 slide feeder, the scanner will not recognize the adapter unless the connector on the rear of the adapter is fully inserted in the connector at the back of the adapter slot. Problem: the status LED on the SF-200 does not light If the status LED on the optional SF-200 slide feeder does not light when the adapter is inserted in the scanner, check the following items. [. . . ]