User manual NIKON R10

[. . . ] 2 If corrosive liquids seep from the batteries and come in contact with your skin or clothes, wash immediately with running water. Prolonged contact could injure your skin. 3 Never attempt to disassemble or repair the flash unit by yourself, as this could result in you receiving an electric shock and could also cause the unit to malfunction; such malfunction could lead to personal injury. 4 If the flash unit is dropped and damaged, do not touch any exposed interior metal parts. [. . . ] The last value to blink is the one that has been set automatically. Details on close-up flash operation and shooting procedures 75 3 Procedures for close-up flash operation 7 Setting the manual flash output level for group C. Press the [SEL](FUNC. ) button to display manual flash output level (blinking) for group C, then press the [] or [] button to increase or decrease the value. Press the [SEL](FUNC. ) button once again and the flash output level stops blinking. The last value to blink is the one that has been set automatically. · Manual flash output level can be set separately for each group. · The flash output level can be set from M1/1 to M1/64. (M1/8 is preset when shipped from the factory. ) · Press and hold the [] or [] button to quickly increase or decrease the value. · The flash output level ratio blinks during adjustment and stops after blinking six times unless an adjustment is made. The last value to blink is the one that has been set automatically. 8 Setting a channel number on the SU-800. Set the communication channel numbers of the SU-800 and SB-R200. Press the [SEL](FUNC. ) button to display the channel number (blinking). Press the [] or [] button to set the channel number. F-3 was taken using a single built-in flash. Flash setup Example G G-1 Group A SB-R200 SU-800 Group C SB-R200 Details on Commander flash operation and shooting procedures Triple-light flash operation To create a more natural looking picture of flowers in terms of colors and textures, one SB-R200 from the top is used as a main flash unit in addition to lighting setups from the front and rear. Two SB-R200 attached to the front of the lens eliminate harsh shadows. Another SB-R200 bounced from the rear emphasizes the subject contours and brightens the backgrounds. SB-R200 Group A SB-R200 Group B · Camera: D70 · Lens: AF Micro-Nikkor 105mm f/2. 8D · Group A: SB-R200 (TTL) · Group B: SB-R200 (TTL) · Group C: SB-R200 (M) G-2 example in "Close-up Speedlight Photography Examples" was taken using flash units in Groups A and B. G-3 was taken using flash units in Group A only. 81 2 Overview of Commander flash operation Example J J-1 Flash setup SU-800 Group A SB-R200×8 SB-R200 Group B Dual-light flash operation Ring-type lighting is used with a total of eight SB-R200 units attached to the Attachment Ring SX-1. Another SB-R200 is placed behind to bounce the light off the background wall to create a magical atmosphere. · Camera: D70 · Lens: AF-S DX Zoom-Nikkor 18-70mm f/3. 5-4. 5G IF-ED · Group A: SB-R200 (TTL) x8 · Group B: SB-R200 (TTL) J-3 and J-4 examples in "Close-up Speedlight Photography Examples" was taken under the same conditions as with J-1. J-2 was taken using a single flash unit. Commander and remote flash units Commander flash operation is possible when CLS-compatible cameras are used with the following Commander and remote flash units. The Commander flash unit provides wireless control of the flash operation of 3-grouped (A, B, C) remote flash units. Flash units usable as a Commander unit · Wireless Speedlight Commander SU-800 · CLS-compatible cameras with Commander function · Speedlight SB-800 Flash units usable as a remote flash unit · Wireless Remote Speedlight SB-R200 · Speedlight SB-800, SB-600 SB-800's Commander mode In the Commander mode, although the SB-800 is set as the Master flash unit and its flash mode is set to Flash Canceled (---), the flash will fire at a reduced flash output level. This may affect the correct exposure of the subject if the subject is close. To limit this effect as much as possible, bounce the light by tilting or rotating the SB-800's flash head. Notes on performing Commander flash operation Available Commander functions and necessary settings vary depending on the cameras and remote flash units in use. [. . . ] 90 Test firing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Triple-light close-up flash operation . . . . . . . . 68 Two-button reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 N NO AF-ILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]