User manual NIKON SF-200

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual NIKON SF-200. We hope that this NIKON SF-200 user guide will be useful to you.

Lastmanuals help download the user guide NIKON SF-200.


Mode d'emploi NIKON SF-200
Download

You may also download the following manuals related to this product:

   NIKON SF-200 REFERENCE MANUAL (333 ko)

Manual abstract: user guide NIKON SF-200

Detailed instructions for use are in the User's Guide.

[. . . ] The address of Nikon's representative in your area is provided separately. · Nikon is not liable for damages resulting from the use of this product. Trademark Information All trade-names mentioned in this manual are the trademarks or registered trademarks of their respective holders. Symbol The symbols in this manual signify important safety precautions. All passages marked with this indication should be read prior to installation to prevent injury to yourself or to others. Symbol The symbols in this manual signify the need for caution when using the product. [. . . ] The scanner must be on its base before the SF-200 (S) can be inserted. If the scanner is currently installed on its side, turn the scanner onto its base. Slide the SF-200 (S) into the scanner's adapter slot, stopping when the feeder contacts the back of the slot. The feeder should be oriented as shown below when inserted. Push the feeder until the connector on the rear of the feeder is seated securely in the socket at the back of the slot. The feeder is properly inserted if the status LED on the front of the feeder lights when the scanner is turned on. If the scanner is on when the feeder is inserted, the feeder's status LED will blink to indicate that the feeder has been inserted correctly. In all other respects, the feeder LED functions in the same way as the scanner status LED. Power switch Status LED The illustration shows the SUPER COOLSCAN 4000 ED If the feed mechanism for the SF-200 (S) is not in the initial position when the scanner is turned on, you will need to wait a few seconds for the feed mechanism to return to initial position before inserting slides. Cautions · Wait until the status LED glows steadily or the scanner is off before inserting or removing the SF-200 (S). Do not attempt to remove or insert the feeder while the scanner is operating. · When the SF-200 (S) is inserted with the power on, or the scanner turned on after the feeder has been inserted with the power off, the feed mechanism will return to the initial position. While this operation is in progress, the status LED on the front of the feeder will blink. Do not perform any operations while the LED is blinking. · If the feeder does not slide in smoothly, remove it from the adapter slot and try again. Using the SF-200 (S) This chapter describes how to load the SF-200 (S), how to remove slides, and how to deal with jams. 4. 1 Loading the feeder Slides to be scanned are inserted in the feed magazine. To load the magazine, open the magazine cover, pull back the feed push-plate to the end of its grove, and hook it in the notch so that it does not spring back to its original position. Place the slides in the magazine with the long end of the aperture up and the emulsion surface facing the push plate (the images in the slides should be reversed when viewed from the magazine side). Scanning will be considerably simplified if the slides are all inserted in the same orientation. Magazine cover Push plate Ejection magazine Notch Load mark Slides can be loaded into the feed magazine up to the load mark. Do not attempt to fill the magazine past this point. Once the feed magazine is loaded, release the push plate from the notch and slide it back until rests against the slides. Close the magazine cover. For details on automatic consecutive scanning of multiple slides, refer to the software reference manual. 24 Cautions · Slides must be from 1. 0 mm to 3. 2 mm thick. [. . . ] 5. 2 Storage When you do not plan to use the feeder for an extended period of time, remove it from the scanner. Store in a dry, well-ventilated environment, away from electronic equipment such as televisions or radios which produce strong magnetic fields. Do not store the feeder where the temperature exceeds 60ºC (140ºF) or goes below ­20ºC (­4ºF), or where the humidity is less than 20% or more than 90%. 5. 3 Transport When transporting the scanner, remove the feeder from the scanner and pack it in the original packing material. 31 6. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE NIKON SF-200

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual NIKON SF-200 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag