User manual NIKON WP-CP2 (SUPPORTS COOLPIX 5200/4200)

[. . . ] WATERPROOF CASE En User's Manual For Your Safety To prevent damage to your Nikon product or injury to yourself or to others, read the following safety precautions in their entirety before using this equipment. Keep these safety instructions where all those who use the product will read them. The consequences that could result from failure to observe the precautions listed in this section are indicated by the following symbol: This icon marks warnings, information that should be read before using this Nikon product to prevent possible injury. WARNINGS Turn camera off immediately in the event of malfunction Should you notice smoke or an unusual smell coming from the equipment, remove the battery from the camera immediately, taking care to avoid burns. Continued operation could result in injury. [. . . ] Additional compatibility information may be available from the websites listed below. Important: Before Using This Product Before using this product, be sure that the camera is functioning normally and that the case does not leak ( 6­7, 12). Failure to check for leaks before using the product could result in irreparable damage to the camera, batteries, or memory card. Nikon will not be held liable for damages or lost profits that may result from leakage or product malfunction. Important: Use Only Nikon Brand Electronic Accessories Nikon COOLPIX cameras are designed to the highest standards and include complex electronic circuitry. Only Nikon brand electronic accessories (including battery chargers, batteries, and AC adapters) certified by Nikon specifically for use with this Nikon digital camera are engineered and proven to operate within the operational and safety requirements of this electronic circuitry. For more information about Nikon brand accessories, contact a local authorized Nikon dealer. Life-Long Learning As part of Nikon's "Life-Long Learning" commitment to ongoing product support and education, continually-updated information is available on-line at the following sites: · For users in the U. S. A. : http://www. nikonusa. com/ · For users in Europe and Africa: http://www. europe-nikon. com/support · For users in Asia, Oceania and the Middle East: http://www. nikon-asia. com/ Visit these sites to keep up-to-date with the latest product information, tips, answers to frequently-asked questions (FAQs), and general advice on digital imaging and photography. Additional information may be available from the Nikon representative in your area. See camera Guide to Digital Photography for details. 3 Overview Using the WP-CP2 Follow these steps when using the waterproof case: Check for Leaks ( 6­7) Introduction Important!To prevent water damage to the camera, be sure to check for leaks before placing the camera in the case. If water enters the case, check the O-ring and confirm that the case is properly sealed ( 10). Close the case 4 Introduction Check for Leaks Again ( 12) If water enters the case, check the O-ring and confirm that the case is properly sealed ( 10). If the cause of the leak can not be determined, take the case to a Nikon-authorized service representative. Take Pictures 1. Take pictures ( 13­14) Clean the Case 1. Maintenance · Caring for the O-ring · Storage Wash the case in fresh water Wipe dry Remove the camera Soak the case in fresh water Wipe dry Let the case dry in the shade ( 15­16) ( 17­19) 5 Check for Leaks Important!Before placing the camera in the case, be sure that the camera is functioning normally and that the case does not leak. Failure to check for leaks before use could result in irreparable damage to the camera. Close the case After making sure that the O-ring is in place, slowly close the case, being careful not to pinch your fingers in the gap. Check for Leaks Latch the case With front and rear halves of the case lightly touching but the case not fully closed ( ), flip the buckle onto the front half of the case ( ). Press the case closed until the latch clicks shut. Check that the case is properly sealed, that the O-ring is in place, and that no foreign objects are caught in the seal. Immerse the case Slowly immerse the case in water, stopping if water enters the case. Test the case in a shallow area (1 m / 3´ or less) or in a tub or bucket. [. . . ] Improper handling of the O-ring can produce leaks. Check the condition of the O-ring as described below before each use, and check for the presence of foreign matter on the O-ring each time the case is opened, however briefly. Remove the O-ring Pinch the O-ring lightly between two fingers to form a loop. Take hold of the loop and remove the O-ring from the case. [. . . ]