User manual NILES IPC-6

[. . . ] MODEL IPC-6 IPC-6 INTELLIGENT POWER CONTROLLER PROGRAM A-TRIGGER-B SELECT TIME POWER ON OFF 1 2 3 4 5 6 C1 C2 NILES IPC-6 INTELLIGENT POWER CONTROLLER NILES ® Niles Audio Corporation www. nilesaudio. com 12331 S. W. 130 Street Miami, Florida 33186 Tel: (305) 238-4373 Fax: (305) 238-0185 ©1999 Niles Audio Corporation. Niles and the Niles logo are registered trademarks of Niles Audio Corporation. All other trademarks are the properties of their respective owners. [. . . ] Put the IPC-6 into position and make the connections to it. While carefully observing each label, plug each low voltage connector, switched outlet plug, and triggering component into its respective place (see Figure 2 on page 11). IPC-6 Total Power Capacity Check that the total power consumption of all the devices plugged into the IPC-6 does not exceed 1500 watts. If the total power is greater than 1500 watts, you will need to trigger a Niles AC-3 voltage controlled power strip from one of the IPC-6's 12 volt control outputs. Since the maximum power output of most home outlets is 1500 watts, you'll need to plug the AC-3 into a wall outlet that is on a different circuit breaker than the IPC-6. IPC-6 Low Voltage Contacts (C1 & C2 Controlled Outputs) The IPC-6 has both normally-open and normally-closed contacts to control devices that need a switch to control them. DO NOT connect 120 volts AC to these contacts. 12 Volt Trigger Inputs Do not exceed 1500 watts of total power consumption for the devices plugged into each IPC-6. IMPORTANT Do not connect 120 volt AC power to the C1 and C2 terminals, they are low voltage only! IMPORTANT The IPC-6's external trigger inputs accept 3-30 volts AC or DC. Switched 120 Volt AC Outlets Test each component to determine whether it has the "latching" type of power control. If the component returns to its fully "on" state rather than to a "standby" state it is suitable for use Do not connect any signal higher than 30 volts to the trigger inputs! Figure 1 Connecting the Low Voltage Wires 5 6 I NTELLIGENT P OWER C ONTROLLER I NTELLIGENT P OWER C ONTROLLER Press the PROGRAM and the SELECT buttons at the same time to enter the PS program mode. PROGRAM LED Indicates the IPC-6 is in one of the program modes. The SELECT button steps you through programming each outlet's amount of delay--first for turning on (the on light is lit), then for turning off (the off light is lit). SELECT BUTTON DIGITAL DISPLAY Shows you the currently selected delay. POWER LED Indicates the IPC-6 has power. ON AND OFF LEDS IPC-6 INTELLIGENT POWER CONTROLLER PROGRAM A-TRIGGER-B SELECT POWER ON OFF 1 2 3 4 5 6 C1 C2 03 TIME NILES PROGRAM BUTTON Begins and ends all programming. TRIGGER BUTTONS "A" AND "B" TIME BUTTONS Allow you to adjust the delay between 0 and 99 seconds. 7 OUTLET CONTROL LEDS Normally, these indicate whether the outlet is on or activated. However, if you are in the PS program mode these indicate which outlet is being programming. 8 I NTELLIGENT P OWER C ONTROLLER I NTELLIGENT P OWER C ONTROLLER ACCUSENSETM 120 VOLT AC POWER OUTLETS Turning on the device plugged into one of these outlets will trigger the corresponding (A or B) ON sequence. Turning off the device plugged into one of these outlets will trigger the corresponding (A or B) OFF sequence. CONTROLLED 12 VOLT DC OUTPUTS Positive = Terminal 1 Ground = Terminal 2 POWER CORD Plugs directly into the wall AC outlet. CONTROL OUTPUTS C1 CONTROL OUTPUT RELAYS C1 and C2 rated at 5 Amps, 30 Volts Max. , AC or DC. C NON OMC 12V 0. 1 AMP +C2 C NON OMC 12V 0. 1 AMP +- TRIGGER INPUTS 3-30V 3-30V AC/DC AC/DC ++- CURRENT SENSE OUTLETS SWITCHED OUTLETS 120 Volts AC 60 Hz. 1500 Watts Max. NILES RELAY DC OUT RELAY DC OUT A B A B 1 2 3 4 5 6 Niles Audio Corporation, Inc. Miami, Florida USA CONTACT GROUP ONE CONTACT GROUP TWO SENSING 3-30V AC or DC INPUTS SWITCHED 120 VOLT AC POWER OUTLETS These turn on and off according to the way you have programmed your IPC-6. Contact groups provide you with a NORMALLY OPEN (N. O. ) contact that closes, or a NORMALLY CLOSED (N. C. ) contact that opens when C1 or C2 are activated. = Terminal 3 REMEMBER: THE TOTAL POWER CONSUMPTION OF ALL DEVICES PLUGGED INTO THE IPC-6 MAY NOT EXCEED 1500 WATTS. 10 9 I NTELLIGENT P OWER C ONTROLLER I NTELLIGENT P OWER C ONTROLLER 5. Plug the IPC-6's AC power plug into an unswitched AC power outlet. All the lights on the front panel will light for 2 seconds while the IPC-6's microprocessor checks all conditions. If everything is ok, all but the red POWER LED will turn off. You are now ready to program your IPC-6. Pre-amp Surround Sound Processor Programming You must program your IPC-6 in two steps. The IPC-6's AccusenseTM circuitry needs to measure the "on" and the "standby" states of the device you have connected to the sensing 120 volt AC outlet(s). [. . . ] Adjust the "off" time delay of each. Pressing the SELECT button after you have programmed C2 will cycle you back to programming the "on" time delays. Press the PROGRAM button and release it. All the front panel LED's will light for 2 seconds. [. . . ]