User manual NILES IRD-8

[. . . ] Additionally, the IRD-8 is able to control 2 devices or components which need a 12 volt DC signal to turn on (e. g. , video projectors and electric screens). Finally, the IRD-8 can control 2 devices that require a switch or relay contact closure for operation (e. g. , electric curtains and blinds or low voltage lighting). *Patents applied for. Introduction Features and Benefits 1 3 Unlike other "current-sensing" power controllers, the Niles IRD-8 uses "smart" current-sensing outlets. The IRD-8 is able to automatically sense as little as a 2 watt difference between a component's "on" and "standby" state. [. . . ] Run all the necessary wiring to the IRD-8's planned location. Label the wires with both their origin (which component they power) and their destinati on (which of the switched outl ets that component wi ll use). Use the Programming Worksheet on Page 17 to write down your choices. You will need a convenient written record when you program your IRD-8. Make the low voltage connections to the IRD-8. If you are using any of the low-voltage inputs or outputs, you should remove the IRD-8's connectors. It is easier to attach the wire to the connector first, before putting the IRD-8 in place. To remove a connector grasp it from the top and bottom with your thumb and forefinger and simply pull straight back. Strip 3/8" of insulation from the end of each wire. Tightly twist the stripped wire to eliminate any frayed ends. Insert each wire into the appropriate hole in the connector block and tighten the terminal with an 1/8" slotted screwdriver. Measuring Power "On" and "Standby" States. Figure 2 Wiring Diagram CONTROL OUTPUTS C1 CONTROL OUTPUT RELAYS C1 and C2 rated at 5 Amps, 30 Volts Max. , AC or DC. C NON OMC 12V 0. 1 AMP +C2 C NON OMC 12V 0. 1 AMP +- TRIGGER INPUTS 3-30V 3-30V AC/DC AC/DC ++- CURRENT SENSE OUTLETS SWITCHED OUTLETS 120 Volts AC 60 Hz. 1500 Watts Max. NILES RELAY DC OUT RELAY DC OUT A B A B 1 2 3 4 5 6 Niles Audio Corporation, Inc. Miami, Florida USA Some devices (television sets, stereo receivers, etc) actually have 3 power states. You can turn them on with a remote control, you can place them in "standby" with a remote control, and you can use a manual power (or "vacation") switch to turn them completely off. You want the IRD-8 to measure what happens to your device when you use the remote control. Unless you are sure there is not a third power state, use the remote control to turn the device on and off. Turn off the device(s) plugged into the "A" or "B" sensing 120 volt AC outlets. In order to enter the "PA" programming mode, press and hold down the PROGRAM button on the front panel of the IRD-8. While you are holding it down, press the "A" Trigger button, then release both buttons. Screen Blind Controller Lighting Controller Equalizer Center Amp Projector 11 Main Amp Surround Amp The front panel LED's will sequence to the left and right while the AccusenseTM circuitry measures your device's stand12 I NTELLIGENT P OWER C ONTROLLER I NTELLIGENT P OWER C ONTROLLER by current. After the sequencing stops, the ON LED should be blinking. This means that the IRD-8 is ready to measure the device's "on" state. [. . . ] Perhaps "A" and "B" have been reversed or are actually plugged into another outlet. Press the PROGRAM button to turn off the display of E1, then begin again at step one. Make sure you are "on" and "off" when the directions say you should be. Cancel Programming At any time, you may stop programming by simply pressing and holding the PROGRAM button for one second. 16 I NTELLIGENT P OWER C ONTROLLER I NTELLIGENT P OWER C ONTROLLER IRD-8 PROGRAMMING WORKSHEET Sense A Outlet Controlled Outlet AC Power #1 AC Power #2 AC Power #3 AC Power #4 AC Power #5 AC Power #6 12 Volt Output Sense B Outlet Device you are controlling Trigger Trigger A B ON Delay OFF Delay Troubleshooting 1. [. . . ]