User manual NILES VDA-6

[. . . ] For a free full-line catalog, write: Niles, Catalog Request, P Box 160818, Miami, Florida 331 . O. 16-0818 Table Of Contents TABLE OF CONTENTS INTRODUCTION . . 13 Configuration 2-Adding Zones Using Multiple A4. 6Ci's . . 15 Configuration 3-Integrating an IR-Controlled Home Theater . [. . . ] The System On/Off Sequence is controlled by the Master A4. 6Ci only. 1 JOB TITLE 2 SYSTEM DESIGNER Mr. Smith Document the customer's name. John Doe Document the system designer's name. 3 (CHOOSE ONE) MASTER SLAVE 1 SLAVE 2 SLAVE 3 ZONE # 3A · Check a box to indicate if it is the Master or Slaves 1-3. · Zone number 3B ZONE ON SEQUENCE STEP DESCRIPTION PAGE KEY ZONE OFF SEQUENCE STEP DESCRIPTION PAGE KEY 1 2 3 4 5 1 2 3 4 5 The steps in the Zone On and Zone Off sequences: · Describe the IR commands, or indicate if there are delays. · Page and key address where the IR commands are stored. 4 x MASTER (THE SYSTEM ON/OFF SEQUENCE IS PROGRAMMABLE FOR THE MASTER VDA-6 ONLY) SYSTEM OFF SEQUENCE PAGE KEY STEP DESCRIPTION PAGE KEY SYSTEM ON SEQUENCE STEP DESCRIPTION 1 2 3 4 5 1 2 3 4 5 The steps in the System On and System Off sequences: · Describe the IR commands, or indicate if there are delays. · Page and key address where the IR commands are stored. 59 PROGRAMMING OVERVIEW Worksheet #6, Function-Key Sequence Programming Worksheet #6 documents the steps of the sequences that have been programmed into any of the available Function Keys for the Master A4. 6Ci only. Identify where the IR commands were programmed by using their page and key address. Copy the worksheet as needed to document all Function Key sequences. Please note that if a Function Key has an IR command programmed and you program a sequence on that same Function Key, the IR command is not erased. It is, however, overridden by the sequence, so the sequence only gets issued whenever that key is pressed. 1 JOB TITLE 2 SYSTEM DESIGNER Mr. Smith Document the customer's name. John Doe Document the system designer's name. 3 FUNCTION KEY SEQUENCES 3A TRIGGER PAGE _________ TRIGGER KEY_________ 3B STEP DESCRIPTION PAGE KEY Indicate the trigger page and the trigger key. (The Trigger Key is the Function Key that will initiate the sequence when pressed. Important Note: IR sensors cannot operate a zone when used alone. They must be installed and connected to a SoloTM or SelectTM Master Keypad Module. The commands you will teach from the Niles R-4 Remote to the learning remote are stored in the following buttons: Source Buttons: Tuner, 2, 3, and 4. These activate the system, turn the zones on, and select the desired source. The Tuner button is equivalent to Master Key #1. Function Buttons to issue the IR commands for each of the individual source components. Volume and Mute buttons to control the volume in a zone. To teach these commands, set the learning remote that you will use in the zone, to the learning mode, choose the appropriate key on the learning remote, and then issue the appropriate command from the Niles R-4 Remote. Repeat these steps for the remaining commands you wish to use. To test the commands, set the Niles remote aside, and try the commands on your learning remote. If they were captured correctly, you will be operating the system and all the source components identically to the Niles R-4 Remote. Niles R-4 Remote Learning Remote Control Figure 52 PROGRAMMING A HOME THEATER REMOTE TO OPERATE SOURCE COMPONENTS SHARED WITH AN A4. 6Ci. [. . . ] · Used to send sync signals to the 12V sync inputs of the IntelliControl®. Connects with a 3. 5mm mono miniplug to 3. 5mm. OTI-512 Opto-Isolated Voltage Trigger STOCK # 10' Mini-plug to Mini-Plug Accessory Cable STOCK # FG00319 Converts any voltage between 3V and 30V (AC or DC) to 12V DC sync. Useful in combination with an accessory cable with ProceedTM, FosgateTM, CitationTM, and SynthesisTM preamps. FG00933 · 10' 3. 5mm mono mini to 3. 5mm mono mini-cable. · Used to send sync signals to the 12V sync inputs of the IntelliControl®. [. . . ]