User manual NILFISK 6150

[. . . ] AMERICAN-LINCOLN TECHNOLOGY OPERATOR'S MANUAL & PARTS LIST 6150 POWER SWEEPER Beginning with Serial No. 630951 READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. you must have training in the operation of this machine before using it. [. . . ] Be sure accelerator and directional control pedal is in neutral. PRE-START CHECK LIST Before starting the engine, perform these pre-start checks. Check engine air filter element indicator. Check brakes and controls for proper operation. Check to ensure that all covers, panels and access doors are securely closed. NOTE When Machine Has Been Stored In Below Freezing Temperatures, Run Engine At The "1" (low) Speed Setting With Machine Standing Still For 5 To 10 Minutes To Warm Engine And Hydraulic Oil. TO START BATTERY MACHINES Starting the battery powered models is accomplished by turning the key switch to the "I" (on) position. It is important to note that the batteries should be fully charged and serviced prior to using the machine. TO CHARGE BATTERIES Charge the batteries at the end of each day or when the battery condition meter indicates low battery voltage. The batteries need to be charged when the needle stays in the "red" zone while the machine is being operated. When charging batteries, only use the quick disconnect provided ensure correct polarity. Follow the "Battery Charging Instructions" provided in the service section of this manual. TO START GAS ENGINE Use the choke in extremely cold temperatures, (under 32 F. Set the engine speed switch to the "1" (low) Speed setting. Turn key to "START" position until engine starts, then release. (The key switch will return to the "ON" position. ) 4. Push in choke after engine starts running (If used). TO START PROPANE ENGINE Perform these checks in addition to the Pre-Start check list. Momentarily press fuel primer on the regulator cover to bleed air out of the system. Set the engine speed switch to the "IDLE" (low) Speed setting. Turn key to "START" position until engine starts, then release. (The key switch will return to the "ON" position. ) 1-26 American-Lincoln 6150 OPERATING INSTRUCTIONS TO START DIESEL ENGINE When starting the diesel engine, it should be noted that under no circumstances should Ether or any other starting fluids be used in conjunction with the glow plugs. Do not use the glow plugs for more than 60 seconds at a time or damage to the plugs may result. [. . . ] Bearing Flat Washer, 1. 125 x . 765 x . 062 Tye - Wrap Terminal Terminal, 1/4 x . 03 12-10 Cotter Pin, . 063 x. 500 Flat Washer, 1. 375 x . 563 x . 109 SS Washer, Spring, Shakeproof Flat Washer, . 750 x . 343 x . 050 SS Screw, . 25 - 20 x 2. 25 HHC Screw, HSHC . 31 - 18 x 1. 00 Nut, 3/8 - 32 NEF 2A Screw, RHM #10-32 1/4 PL. (Steel) Sealing Washer 46/53 ESP OPT Screw - T/C RH #8-32x. 50type 2 Washer Flat, 2 x 1. 06 Screw, HHC M14 x 1. 50 x 45mmgr10 Screw, HHC . 438 - 20 x 1. 50 Bolt Carriage, . 31 - 18 x 1. 75 Nut, . 38-16 Hex heavy Jam Screw, RHM #8-32 x . 50 Screw, . 313-18 x 4. 00 HHC Screw, BTN HD SKT Nut, Hex Hvy, . 50-13 stl-zn. Screw, Shoulder 1/2-1/2 Screw, HHC, . 375-16 x 2. 75 Screw, HHM 3/4-16 x 3. 000 Screw, HHC . 25-20 x 1. 000 Screw, HHC M10 x 1. 50 x 40MM SS Screw, Ph. Screw HHC . 375-16 x 1. 75 #10-24 BHCS 1. 00 Black Oxide Carriage Bolt, . 31-18 x 1. 50 Screw, RHM #10-24 x . 25** NLS Flatwasher . 875 x . 516 x . 031 ss Fhms #10-32 x . 312 M16 x 1. 50 Hex Nut (Metric) Gr 10. 9 Flatwasher . 750 x . 312 x . 065 ss-zn Shoulder Screw, 5/16-18 x 3/8 Clamp - Witteck - C24P O-Ring 1-57 HARDWARE ABBREVIATIONS ABBREVIATIONS - SCREWS = = = = = = = = = = = = = = = = = = = = = = = = = = Adjusting Screw Adjusting Plunger Screw Binding Head Machine Screw Button Head Socket Screw Captivated Slotted Screw Captivated Wing Screw Flat Head Machine Screw Filister Head Machine Screw Hexagon Head Cap Screw Hexagon Head Machine Screw 1/2 High Head Screw Hexagonal Socket Head Cap Screw Hexagonal Socket Flat Head Cap Screw Knurled Head Screw Metric Hexagon Head Cap Screw Pan Head Machine Screw Round Head Drive Screw Round Head Machine Screw Round Head Wood Screw Shiny Crown Cap Screw Shoulder Thumb Screw Square Head Screw Thumb Screw Truss Head Machine Screw Weld Stud Wing Screw ADJ ADJ. SP BHM BHS CAPT. SL CAPT. WG FHM FIL. HM HHC HHM HIHD HSHC HSFHC KNH MHHC PHM RHD RHM RHW SHC SHTB SQ TB THM WELD WG ABBREVIATIONS - SETSCREWS = = = = = = = = = = Hexagonal Socket Setscrew Slotted Setscrew Square Head Setscrew Knurled Cup Point Setscrew Cup Point Setscrew Oval Point Setscrew Full Dog Point Setscrew Half Dog Point Setscrew Flat Point Setscrew Cone Point Setscrew HS S SH -KCP -CP -OP -FDP -HDP -FP -COP C-2004 1-58 American-Lincoln 6150 ORDERING PARTS INTERNET http://www. alto-online. com CZECH REPUBLIC ALTO Ceská Republika s. r. o. [. . . ]