User manual NILFISK CA 410

[. . . ] The undersigned certify that the above mentioned model is produced in accordance with the following directives and standards. Support brosse / plateau support disque 26. Support brosse / plateau support disque 34. Caractéristiques générales Longueur machine Largeur machine avec embouchure Largeur machine sans embouchure Hauteur minimum / maximum machine avec guidon réglable Poids total machine Rayon minimum de braquage Largeur de nettoyage Diamètre roues centrales sur essieu fixe Diamètre brosse / disque Pression roues arrière au sol Pression roulette avant au sol Pression brosse / disque au sol Performances Aspiration Vitesse moteur brosse / plateau support disque Pression acoustique à l'oreille de l'opérateur (ISO 11201, ISO 4871) (LpA) Puissance acoustique émise par la machine (ISO 3744, ISO 4871) (LwA) Niveau de vibrations au bras de l'opérateur (ISO 5349-1) Puissance moteur système d'aspiration Puissance moteur brosse / plateau support disque Pente maximum franchissable Tension système Capacité réservoir solution Capacité réservoir eau de récupération 230 V - 50 Hz 23 litres 21 litres 1 100 W 2% 115 V - 60 Hz 150 tr/mn 87 dB(A) < 2, 5 m/s2 550 W 550 W CA 410 - 230 volts CA 410 - 230 volts 997 mm 720 mm 570 mm 730 - 836 mm 65 kg 750 mm 430 mm 250 mm 430 - 432 mm 1, 0 N/mm2 1, 9 N/mm2 28 kg CA 410 - 115 volts 170 tr/mn CA 410 - 115 volts C1 EV1 FR M1 M2 PL SW1 SW2 Suppresseur Electrovanne eau Cadre Moteur brosse / plateau support disque Moteur système d'aspiration Fiche Interrupteur brosse / plateau support disque Interrupteur système d'aspiration Appuyer sur le bouton-poussoir de brosse / plateau support disque (52) pendant quelques secondes pour permettre l'accrochage de la brosse / plateau support disque. [. . . ] ­ Do not allow the brush/pad to operate while the machine is stationary to avoid damaging the floor. ­ In case of fire, use a powder fire extinguisher, not a water one. ­ Do not tamper with the machine safety guards and follow the ordinary maintenance instructions scrupulously. ­ Do not allow any object to enter into the openings. Do not use the machine if the openings are clogged. Always keep the openings free from dust, hairs and any other foreign material which could reduce the air flow. Do not remove or modify the plates affixed to the machine. ­ This machine cannot be used on roads or public streets. ­ Pay attention during machine transportation when temperature is below freezing point. The water in the recovery tank or in the hoses could freeze and seriously damage the machine. ­ Use brushes and pads supplied with the machine and those specified in the User Manual. Using other brushes or pads could reduce safety. In case of machine malfunctions , ensure that these are not due to lack of maintenance. Otherwise, request assistance from the authorised personnel or from an authorised Service Center. Has been left outdoors exposed to bad weather conditions · Is wet or has been dropped into water turn it off immediately and contact the Nilfisk Service Center or a qualified technician. ­ If parts must be replaced, require ORIGINAL spare parts from an Authorised Dealer or Retailer. ­ To ensure machine proper and safe operation, the scheduled maintenance shown in the relevant chapter of this Manual, must be performed by the authorised personnel or by an authorised Service Center. ­ Carefully read all the instructions before performing any maintenance/repair procedure. ­ Do not wash the machine with direct or pressurised water jets, or with corrosive substances. ­ The machine must be disposed of properly, because of the presence of toxic-harmful materials (electronic components, etc. ), which are subject to standards that require disposal in special centres (see the Scrapping chapter). Serial number plate/technical data/conformity certification Handlebar Handlebar inclination adjusting knob Solution flow control lever Solution flow control lever ECO position (water "economy" usage, for a washing autonomy set for 70-80 minutes) Recovery tank cover Rear support wheel for transport/parking Central wheels on fixed axle Brush/pad Brush/pad-holder deck Squeegee Squeegee mounting handwheels Front squeegee blade Rear squeegee blade Squeegee blade mounting springs Recovery water drain hose 17. [. . . ] Also check the front corner (H) of the rear blade for wear; if it is worn, overturn the blade to replace the worn corner with the other one (I), if it is integral. If the other corner is worn too, replace the blade according to the following procedure: · NOTE It is advisable to wear protective gloves when cleaning the brushes because there may be sharp debris. Clean the brush with water and detergent. Make sure that the power supply cable (21) is disconnected from the electrical mains. [. . . ]