User manual NILFISK FLOORTEC 350

[. . . ] The undersigned certify that the above mentioned model is produced in accordance with the following directives and standards. The purpose of this Manual is to provide the operator with all necessary information to use the machine properly in a safe and autonomous way. It contains information about technical data, safety, operation, storage, maintenance, spare parts and disposal. Before performing any procedure on the machine, the operators and qualified technicians must read this Manual carefully. [. . . ] ­ Do not use the machine as a means of transport. ­ Do not use the machine on slopes with a gradient exceeding the specifications. ­ Do not allow the brooms to operate while the machine is stationary to avoid damaging the floor. ­ In case of fire, possibly use a powder fire extinguisher, not a water one. ­ Do not bump into shelves or scaffoldings, especially where there is a risk of falling objects. ­ Adjust the operation speed to suit the floor conditions. ­ This machine cannot be used on roads or public streets. ⭠Do not remove or modify the plates affixed to the machine. ­ Do not tamper with the machine safety guards and follow the ordinary maintenance instructions scrupulously. ­ Use only brooms supplied with the machine and those specified in the User Manual. ⭠In case of machine malfunctions , ensure that these are not due to lack of maintenance. Otherwise, request assistance from the authorised personnel or from an authorised Service Center. ­ Carefully read all the instructions before performing any maintenance/repair procedure. ­ To ensure machine proper and safe operation, the scheduled maintenance shown in the relevant chapter of this Manual must be performed by the authorised personnel or by an authorised Service Center. ­ If parts must be replaced, require ORIGINAL spare parts from an Authorised Dealer or Retailer. ­ The machine must be disposed of properly, because of the presence of toxic-harmful materials (batteries, plastics, etc. ), which are subject to standards that require disposal in special centres (see the Scrapping chapter). When turned to "I" the vacuum system and main broom are turned on; · When turned to "II" the vacuum system, main broom and side broom are turned on. Charged battery warning light (green) Semi-discharged battery warning light (yellow) Discharged battery warning light (red) Drive control lever Handlebar Handlebar adjusting knobs Filter shaker knob Hopper Front steering wheel Side broom Side broom lifting/lowering lever Side broom height adjusting knob Main broom Main broom height adjusting knobs Rear driving wheels Can holder Battery charger cable Battery charger cable housing Side broom motor circuit breaker Main motor circuit breaker Battery Dust filter Side broom motor Main motor Drive system gear Vacuum fan Battery charger 29. 5 A) Hood Hopper upper handle Hopper lower handles Serial number plate/technical data/conformity certification Side skirts Front skirt Rear skirt Drive belt adjuster In addition to the standard components, the machine can be equipped with the following accessories/options, according to the machine specific use: 1. General Cleaning width (without side broom) Cleaning width (with side broom) Machine size with folded handlebar and without side broom (length x width x height) Minimum distance from the floor (skirts not included) Main broom size (diameter x length) Side broom diameter Main broom speed Side broom speed Gradeability Hopper capacity Total machine weight (with standard battery) Front steering wheel size (diameter x length) Rear wheel size (diameter x length) Maximum drive speed Sound pressure level at workstation (ISO 11201, ISO 4871) (LpA) Machine output acoustic power (ISO 3744, ISO 4871) (LwA) Vibration level at the operator's arms (ISO 5349-1) Values 500 mm 720 mm 998 x 797 x 621 mm 25 mm 200 x 500 mm 315 mm 335 rpm 100 rpm 2% 60 litres 68 kg 75 x 32 mm 300 x 45 mm 3. On some points of the machine there are some adhesive plates indicating: ­ DANGER ­ WARNING ­ CAUTION ­ NOTE While reading this Manual, the operator must pay careful attention to the symbols shown on the plates. [. . . ] 5) completely on the left side of the machine. 7) on the points (B) and (C), then disconnect it from the drive hub (D) by pulling it in the direction shown by the arrow (E); then remove it in the direction shown by the arrow (F). The new main broom must be installed with the bristles rows bent as shown in the figure. install the new broom by performing steps 3 to 6 in the reverse order. [. . . ]