User manual NILFISK FLOORTEC R 570

[. . . ] It contains information about technical characteristics, operation, machine storage, maintenance, spare parts and safety conditions. Before carrying out any procedure on the machine, the operators and technicians in charge of the machine maintenance must read this manual carefully. All necessary operating, maintenance and repair procedures must be carried out by qualified personnel or by Nilfisk-Alto Service Centers (listed at the end of this manual). Only original spare parts and accessories must be used. [. . . ] Call the Carrier immediately to fill in a damage claim. Please check that the following items have been supplied with the machine: 1. The sweeper is used to sweep dust or light debris on smooth and solid floor, in civil or industrial environment, under safe operation conditions by a qualified Operator. NOTE Forward, backward, front, rear, left or right are intended with reference to the operator's position, that is to say on the driver's seat with the hands on the handlebar (3, Fig. Display selection button: hour counter/ hour and minutes counter / battery voltage (V), 8. Dimensions Cleaning width without side broom Cleaning width with side broom Machine length with lowered handlebar Machine width, without side broom Height when the handlebar is lowered Minimum height from ground Handlebar height, minimum/maximum Main broom size Side broom size Speed with maximum push force Gradeability Hopper capacity Machine weight without battery Front wheel, steering Rear wheels, driving Electric motor Sound pressure level (LpA) In addition to the standard components, the machine can be equipped with the following accessories/options, according to the machine specific use: ­ Gel batteries; ­ Electronic battery charger; ­ Main and side brooms with harder or softer bristles; ­ Antistatic polyester or polyester BIA C dust filter; ­ Electric filter-shaker; ­ front wheel with brake pedal. On some points of the machine there are some adhesives indicating: ­ DANGER ­ WARNING ­ CAUTION ­ NOTE While reading this Manual, the Operator must pay particular attention to these symbols. Do not cover these adhesives for any reason, in case of damage replace them immediately. U) CH1 Battery charger CN1 Battery connector CN2 Battery charger connector EB1 Electronic board ES1 Electromagnetic switch F1 Main fuse F2 Side broom fuse (15A) F3 Filter-shaker fuse (15A) M1 Main broom motor M2 Side broom motor M3 Filter-shaker motor R1 Filter-shaker relay SW1 Key switch SW2 Hood safety switch SW3 Filter-shaker switch According to the chosen battery type (lead or gel) perform the setting of the electronic board of the machine and the battery charger (if installed on the machine), operating as indicated below: The machine needs a 12 V battery or two 6 V batteries connected according to the diagram in Fig. The machine can be equipped: a) (Lead or gel) battery installed on the machine and ready to be used. Lower the hood and check that it is correctly closed (the machine must be as shown in Fig. Avoid stopping for a long time with the machine in the same position and the brooms rotating: this could create unwanted marks on the floor. For the machine to sweep properly the dust filter must be as clean as possible. To clean the filter while sweeping, activate the filter-shaker proceeding as follows and according to the type of filter-shaker installed: a) Manual filter-shaker: turn the ignition key to "0" position, pull the handle outward (20, Fig. C) till the end of stroke, and then release it. the internal return spring strikes the dust filter frame and shakes it. Turn the ignition key to "I" position. While working, repeat the operation every 10 minutes on average (depending on the dustiness of the area to be cleaned). During this operation the main engine and all functions are automatically stopped. C) should be emptied after each working period and whenever is full. To stop the machine, turn the key (1, Fig. C), lift the handle (12) (without turning it) and engage its retainer (2). [. . . ] It is advisable to use protective gloves when replacing the main or side brooms because there can be cutting debris between the bristles. C) and remove the right cover (24) together with the belt (12, Fig. When the recharging is complete, disconnect the battery charger from the electrical system and from the battery connector (3, Fig. Check the correct level of electrolyte inside the battery and close the caps (8). [. . . ]