User manual NILFISK FLOORTEC R 670 P

[. . . ] Nilfisk Alto will not be answerable for damages coming from the non-observance of this prohibition. The User Manual must be kept near the machine, inside an adequate case, away from liquids and other substances that can cause damage to it. The declaration of conformity, supplied with the machine, certifies the machine conformity with the law in force. NOTE Two copies of the original declaration of conformity are provided together with the machine documentation. [. . . ] ⭠Do not use the machine in excessively dusty areas. ­ Do not allow to be used as a toy. Close attention is necessary when used near children. ­ Use only as shown in this Manual. use only Nilfisk Alto's recommended accessories. ­ Take all necessary precautions to prevent hair, jewels and loose clothes from being caught by the machine moving parts. ­ Do not wash the machine with direct or pressurised water jets, or with corrosive substances. Do not use compressed air to clean this type of machine. ­ While using this machine, take care not to cause damage to other people, and children especially. ­ Do not put any can containing fluids on the machine. ­ The machine storage temperature must be between 0°C and +40°C. General Cleaning width (without side broom) Cleaning width (with side broom) Machine size with folded handlebar and without side broom (length x width x height) Minimum distance from the floor (skirts not included) Main broom size (diameter x length) Side broom diameter Main broom speed Side broom speed Gradeability Hopper capacity Total machine weight (with standard battery) Front steering wheel size (diameter x length) Rear wheel size (diameter x length) Maximum drive speed Sound pressure level at workstation (ISO 11201, ISO 4871) (LpA) Machine output acoustic power (ISO 3744, ISO 4871) (LwA) Vibration level at the operator's arms (ISO 5349-1) Values 500 mm 720 mm 998 x 797 x 621 mm 25 mm 200 x 500 mm 315 mm 335 rpm 100 rpm 2% 60 litres 68 kg 75 x 32 mm 300 x 45 mm 3. On some points of the machine there are some adhesive plates indicating: ­ DANGER ­ WARNING ­ CAUTION ­ NOTE While reading this Manual, the operator must pay careful attention to the symbols shown on the plates. Do not cover these plates for any reason and immediately replace them if they are damaged. The machine is supplied with a standard 12 V, 45 Ah GEL battery (which does not require maintenance). Make sure that there are no open doors/hoods and that the machine is in normal operating conditions. If the machine has not been used after being transported, check that all the blocks used for the transportation have been removed. Check that side and main broom are installed, otherwise install them (see the procedure in Maintenance chapter). Adjust the handlebar (6) to reach a comfortable position, by loosening the knobs (7). when the adjustment is completed , tighten the knobs. To use the main broom only (14), turn the main switch (1) to "I". To use also the side broom (11), turn the main switch (1) to "II", then lower the side broom by disengaging the lever (12). [. . . ] Procedure Battery charger cable check Side and main broom height check and adjustment Skirt height and operation check Dust filter cleaning and integrity check Hopper gasket check Filter shaker operation check Driving belt and clutch visual inspection Driving belt tensioner adjustment Nut and screw tightening check Motor carbon brush check or replacement (*) (*) (*) (*) (1) (*) Every 10 hours Every 50 hours Every 200 hours Every 400 hours (1) And after the first 8 hours. Carefully check the battery charger cable (18) and the relevant plug for wear, cuts, cracks or other damages. Check the side broom distance from the floor as shown below: · Drive the machine on a level ground and lower the side broom. ⷠKeep the machine stationary and turn on the side broom for a few seconds. [. . . ]