User manual NILFISK SCRUBTEC 343

[. . . ] The undersigned certify that the above mentioned model is produced in accordance with the following directives and standards. Support brosse / plateau support disque 26. Couvercle réservoir eau de récupération (ouvert) Joint d'étanchéité couvercle réservoir eau de récupération Support brosse / plateau support disque Compartiment réservoir eau de récupération Goulotte de remplissage réservoir solution Grille d'aspiration avec fermeture automatique à flotteur Orifice de drainage eau de récupération Moteur système d'aspiration Moteur brosse / plateau support disque Tête porte-brosses / plateaux support disque Vis de réglage vitesse d'avance machine Brosse Plateau support disque Disque Boîte à bornes Vis Orifice de compensation Tige de blocage couvercle (insérée) Sens de rotation pour accrochage brosse / plateau support disque Performances Aspiration Vitesse moteur brosse / plateau support disque Pression acoustique à l'oreille de l'opérateur (ISO 11201, ISO 4871) (LpA) Puissance acoustique émise par la machine (ISO 3744, ISO 4871) (LwA) Niveau de vibrations au bras de l'opérateur (ISO 5349-1) Puissance moteur système d'aspiration Puissance moteur brosse / plateau support disque Pente maximum franchissable Tension système Contenance réservoir eau propre Capacité réservoir eau de récupération C1 EV1 FR M1 M2 PL SW1 SW2 Suppresseur Electrovanne eau Cadre Moteur brosse / plateau support disque Moteur système d'aspiration Fiche Interrupteur brosse / plateau support disque Interrupteur système d'aspiration Appuyer sur le bouton-poussoir de brosse / plateau support disque (52) pendant quelques secondes pour permettre l'accrochage de la brosse / plateau support disque. REMARQUE Pour un lavage / séchage correct du sol près du mur, Nilfisk Alto recommande d'approcher le côté droit de la machine, comme illustré dans la figure 1. [. . . ] ­ Do not allow the brush/pad to operate while the machine is stationary to avoid damaging the floor. ­ In case of fire, use a powder fire extinguisher, not a water one. ­ Do not tamper with the machine safety guards and follow the ordinary maintenance instructions scrupulously. ­ Do not allow any object to enter into the openings. Do not use the machine if the openings are clogged. Always keep the openings free from dust, hairs and any other foreign material which could reduce the air flow. Do not remove or modify the plates affixed to the machine. ­ This machine cannot be used on roads or public streets. ­ Pay attention during machine transportation when temperature is below freezing point. The water in the recovery tank or in the hoses could freeze and seriously damage the machine. ­ Use brushes and pads supplied with the machine and those specified in the User Manual. Using other brushes or pads could reduce safety. In case of machine malfunctions , ensure that these are not due to lack of maintenance. Otherwise, request assistance from the authorised personnel or from an authorised Service Center. Has been left outdoors exposed to bad weather conditions · Is wet or has been dropped into water turn it off immediately and contact Nilfisk Alto Service Center or a qualified technician. ­ If parts must be replaced, require ORIGINAL spare parts from an Authorised Dealer or Retailer. ­ To ensure machine proper and safe operation, the scheduled maintenance shown in the relevant chapter of this Manual, must be performed by the authorised personnel or by an authorised Service Center. ­ Carefully read all the instructions before performing any maintenance/repair procedure. ­ Do not wash the machine with direct or pressurised water jets, or with corrosive substances. ­ The machine must be disposed of properly, because of the presence of toxic-harmful materials (electronic components, etc. ), which are subject to standards that require disposal in special centres (see the Scrapping chapter). Serial number plate/technical data/conformity certification Handlebar Handlebar inclination adjusting knob Solution flow control lever Minimum solution flow position Maximum solution flow position Recovery tank cover Rear support wheel for transport/parking Central wheels on fixed axle Brush/pad Brush/pad-holder deck Squeegee Squeegee mounting handwheels Front squeegee blade Rear squeegee blade 15. [. . . ] If the other corner is worn too, replace the blade according to the following procedure: · NOTE It is advisable to wear protective gloves when cleaning the brushes because there may be sharp debris. Clean the brush with water and detergent. Make sure that the power supply cable (21) is disconnected from the electrical mains. Open the cover (6), then clean and wash the cover, the tanks (26 and 27) and the vacuum grid (36) with clean water. [. . . ]