User manual NILFISK SPINTEC 343

[. . . ] Check the power cord regularly to detect signs of damage. General Use of the cleaner is subject to current national regulations. Besides the operating instructions and binding accident prevention regulations valid in the country of use, observe recognized regulations for safe and proper work. Do not use the cleaner on public paths and roads. [. . . ] The manufacturer accepts no liability for damage to the cleaner and the cleaned floor that is caused by the use of wrong brushes and cleaning agents. 3 SPINTEC 343 SPINTEC 343 H english 2. 2 Product liability Please note that the cleaners may be used for their intended purpose only. If the cleaners are not used for their intended purpose, the user has the sole responsibility. The manufacturer accepts no liability whatsoever. 2. 3 Operating elements 1 2 3 4 5 6 7 8 9 10 11 Shaft adjustment lever Guide handle Switch lock Socket (SPINTEC 343 H) Brush motor switch Power cord Power cord hook Shaft adjustment joint Wheels Connector for waste hose Shaft Accessories (not included): 12 Spraymaster 13 Tank lever 14 Tank bracket 15 Liquid tank 16 Waste hose 17 Brush 18 Drive plate for pad 19 Pad 3 Before starting the cleaner 3. 1 Assembly 1. Loosen the hexagon socket screws (1) in the shaft adjustment joint (2). 1 2 2. Insert the shaft gently as far as possible into the shaft adjustment joint. Align the handle (3) parallel to the wheels (4) so that the open side of the shaft upper housing faces the rear (5). For transport reasons, the motor head and the shaft are supplied not assembled. 3 5 4. Retighten the hexagon socket screws in the shaft adjustment joint. Wind the power cord around the handle and the power cord hook (6). 6 4 4 SPINTEC 343 SPINTEC 343 H 3. 2 Transport When transporting the cleaner in elevators, observe current safety regulations, in particular with regard to carrying capacity. When transporting the cleaner in elevators, place the shaft in an upright position to prevent it from catching on elevator shaft walls. 1. Grasp the handle with both hands and tip the cleaner until it stands on the two wheels. Wheel the cleaner to where it is needed. english 4 Control/Operation 4. 1 Electrical connections 1. Plug the cleaner into a socket. CAUTION!Connect the cleaner to a proper electrical installation only. Follow safety instructions in Chapter 1. 4. 2 Using accessories 1. Place the accessory (brush or drive plate with pad) on the floor. Tip the cleaner on to its wheels and push it over accessory until the drive star and the brush flange are vertically aligned. Pull the shaft adjustment lever (1) and lower the shaft into its cleaning position. Always guide the cleaner with both hands on the handle (3). Align the cleaner horizontally on the accessory. 2 1 3 5 SPINTEC 343 SPINTEC 343 H english 6. Press the switch lock (4) and briefly press the brush motor switch (5). The brush motor runs and the accessory automatically engages. 4 5 4. 3 Manoeuvring the cleaner 2 1 3 1. Pull the shaft adjustment lever (1) and lower the shaft into its cleaning position. [. . . ] If the cleaner is not to be used, store it in a dry place with normal room conditions (not below 0C). 9 SPINTEC 343 SPINTEC 343 H english 7 Maintenance 7. 1 Maintenance plan Every week Check power cord Clean cleaner, brush holder and accessories using a damp cloth As required Do the work described in the operating instructions only. Before starting any work, unplug the cleaner. Leave service and repair work, in particular repairs concerning electrical faults, to Nilfisk-Alto customer service or authorized persons. 7. 2 Maintenance work 8 Troubleshooting Fault Brush motor does not start Brush motor does not run fast enough Cause > No power Remedy Check power cord, electrical socket and fuse Check combination of cleaning agent, floor covering and accessory Contact Nilfisk-Alto customer service > Too much friction on the floor covering or the brush or pad do not fit the cleaner > Defective starting relay 9 Further information 9. 1 Recycling the cleaner Make the old cleaner unusable immediately. Unplug the cleaner and cut the power cord. [. . . ]