User manual NILFISK SR 1000S P

[. . . ] The undersigned certify that the above mentioned model is produced in accordance with the following directives and standards. Contrôler la hauteur du sol des balais latéraux, en procédant comme suit : ­ porter la machine sur un sol plat et baisser les balais latéraux ; ­ en gardant la machine en position d'arrêt, tourner les balais latéraux pendant quelques secondes ; ­ arrêter et soulever les balais latéraux, puis déplacer et arrêter la machine ; ­ contrôler que la trace laissée par les balais latéraux est, en extension et orientation, comme indiqué dans la figure (1 et 2, Fig. The purpose of this Manual is to provide the operator with all necessary information to use the machine properly in a safe and autonomous way. It contains information about technical data, operation, storage, maintenance, spare parts and safety. [. . . ] ) Engine oil filler/level check plug Engine oil drain plug Engine belt Main broom belt Main broom drive pulley Vacuum fan Engine silencer Batteries Battery caps Lamellar fuse box (accessories) Drive system thermal fuse Starter and dynamo Manual vacuum system (optional) Switch for machine pushing Battery installation diagrams Dynamo fuse Fuel tap Engine choke lever General Machine length Machine width (without side brooms) Machine height (steering wheel with knob) Cleaning width (with side brooms) Main broom size Side broom size Front driving and steering wheel Rear wheels Total machine weight (with batteries) Maximum forward/reverse speed Gradeability Hopper capacity Cleaning rate (with main broom) Cleaning rate (with main and side brooms) Sound pressure level (LpA) Batteries Battery voltage Starter batteries Petrol engine Make Model Displacement Engine power Specific fuel consumption Values 1, 255 mm 795 mm 1, 173 mm 1, 000 mm Ø 265 mm x 600 mm Ø 420 mm Ø 200 x 50 mm Ø 250 x 50 mm 284. NOTE For other petrol engine data/values, see the relevant Manual. W) by introducing your hand into the compartment (37, Fig. Disengage the parking brake according to the following procedure: ­ Press the pedal (6, Fig. Drive the machine to the working area, by keeping the hands on the steering wheel and pressing the pedal (5, Fig. C) on the front side to move forward and on the rear side to move backward. The drive speed can be adjusted from zero to maximum speed by increasing the pressure on the pedal (5, Fig. C) is equipped with a safety sensor, which allows the machine to be driven by pressing the pedal (5, Fig. C) and, if it is necessary for an easier access to the machine, push the lever (11, Fig. C) forward or backward, to reach a comfortable position. Only in case of very low temperatures, turn the engine choke lever (1, Fig. W) to closed position (2) by introducing your hand into the compartment (37, Fig. Turn on the vacuum system with the lever (3, Fig. C) can be lowered and lifted even when the machine is moving. The side brooms do not rotate when they are lifted, but they rotate when they are lowered. C) and move the machine forward by pressing the pedal (5). In case of emergency, press the emergency push-button (8, Fig. To deactivate the emergency push-button (8), turn it clockwise. to turn off the side brooms (13 and 14 , Fig. U) and the engine, turn the ignition switch (2, Fig. Engage the parking brake according to the following procedure: ­ Press the pedal (6, Fig. C) as necessary, then engage the brake by turning the lever (7, Fig. [. . . ] C) height from the ground is within 0 ­ 3 mm (Fig. If necessary, adjust the skirt height, according to the following procedure: Left skirt: ­ Open the machine hood (10, Fig. U) from the pulley (18); for a easier removal, turn the pulley (18) by operating on the vacuum fan (19) manually. N) larger than 20 mm or cracks (2) larger than 10 mm (for skirt replacement, refer to the Service Manual). [. . . ]