User manual NILFISK SW850P

[. . . ] SW 700 P/B - SW 850 P/B SW 5070 P/B - SW 5080 P/B OPERATING INSTRUCTION S31NUK5080(2)2001-01 CONTENTS S31NUK5080(2)2001-01 Model : Serial No : Power : Total Weight Prod. axel front : Noise level : Voltage : INTRODUCTION/GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] After one hour fill up with acid if necessary. Let battery rest for one hour and proceed with the charging (please refer to the paragraph “MAINTENANCE”). When carrying out the recharge operation, all the caps of the battery have to be open. Before starting the recharge operation, the connector of the battery must be disconnected from the machine. 6 PREPARING A NEW MACHINE (battery version) S31NUK5080(2)2001-01 At the end of the recharge operation close all the caps of the batteries, clean their upper part and remove all possible acid remains. Connect the battery’s connector to the machine. 3- If the machine is supplied with no battery, they have to be procured and mounted. It is recommended to use the service of qualified personnel to choose and to install the new battery. The electric connection cables that are supplied together with the machine can be used for the battery connection. Warning: Before starting the recharge operation, the connector of the battery must be disconnected from the machine. Place the brush as per the figure and make sure that the fixing profiles match perfectly with the relevant holes. Coupling may be helped thanks to a light pressure of your hand. Warning: Do not let the starter handle return to its position quickly; please follow it in its downwards movement. When the engine is slightly warm, slowly bring the starter lever "A" to its original position. The rpm are fixed and must be kept constant. A 10 START-UP (petrol version) S31NUK5080(2)2001-01 If you wish to stop the engine, turn selector "C" onto the "OFF" position. C and turn tap "D" onto the "OFF/CLOSED" position. D 11 USE OF THE MACHINE S31NUK5080(2)2001-01 Lower the side brush. BATTERY VERSION When the motor is in operation, make sure that handle "A" has been lowered (suction enabled); if you pull the drive lever "B" you can adjust the running speed depending onto the quality and onto the quantity of the debris to be picked up. The machine looses traction releasing the lever "B". PETROL VERSION When the engine is running, make sure that handle "A" has been lowered (suction enabled); if you pull the drive lever "B" you can adjust the forward speed depending onto the quality and onto the quantity of the debris to be picked up. The machine looses traction releasing the lever "B". A B A B To collect light and bulky waste materials, lift the flap using the the left side lever. (Do not keep pushing onto the lever for a long time in order not to reduce the suction capability of the machine). In case it is necessary to work onto wet ground, it is of utmost importance to disable the suction function (in order not to damage the papermade filter); just pull (upwards) handle "A" as shown in the figure. If you wish to enable the suction, lift lever "B" as shown in the figure. 12 A B USE OF THE MACHINE S31NUK5080(2)2001-01 For efficient suction operation, the air filter must always be clean. Activate the filter shaker (you can also perform this operation when the machine is working) by pulling and releasing the handle as shown in the figure. Warning: always disable the suction function during this operation. Repeat this operation every 15-20 minutes depending on the kind of dirt that is picked up, before emptying the container and at the end of the work. Before leaving the machine, please make sure that: - the side brush is not in contact with the ground. BATTERY VERSION The start-up key is in the "OFF" position. PETROL VERSION The selector is in the "OFF" position. The vaste container should be emptied after each work period and when ever is full. BATTERY VERSION This version includes, as an optional accessory, the electrically-operated filter-shaker which is controlled by means of push-button "A". When using the filter shaker the suction fan will automatically stop. A 13 CENTRAL BRUSH ADJUSTMENT AND REPLACEMENT Warning: these operations must be carried out with the machine off, the key switched off (for battery-operated version), selector in "OFF" position (for petrol-operated version) and with the machine on even floor. When the main brush is fairly worn, its height must be adjusted to recover as much of the brush consumption as possible. Loosen the knobs "A" on both sides of the machine, lower the brush to the ground taking the "B" indicator to the right position in the direction shown in the figure. The "B" indicator must be placed in the same position on both sides of the machine. S31NUK5080(2)2001-01 A A B To make sure that the main brush has been properly adjusted, perform the following operations: let the brush rotate with the machine not in operation and on a flat ground; then make sure that the print left by the brush onto the ground is from 2 to 4 cm. [. . . ] Doornveid/Sphere Business Park Industrie Asse 3, nr 11- bus 41 1731 Zellik-Asse Tel. (02) 467. 60. 50 Fax (02) 463. 44. 16 CANADA Nilfisk-Advance Ltd 396 Watline Avenue Mississauga, Ontario L4Z 1X Tei. (905) 712-3260 - Fax (905) 712-3255 DANMARK Nilfisk-Advance Nordic A/S Myntevej 3, 8900 Randers Tel. 86 42 84 33 - Fax 86 41 19 55 DEUTSCHLAND Nilfisk-Advance AG Siemensstraße 25-27 25462 Rellingen Tei. (04101) 3990 - Fax (04101) 399191 Zentraler Kundenservice / Customer Hotline Tel. 0180 53 56 797 ESPAÑA Nilfisk-Advance, S. A. Torre D’Ara Passeig dei Rengie, 5 -P1. 10 E-08302 Mataró (Barcelona) Spain Tel. : 93 741 2400 Fax: 93 757 8020 nilfisk@nilfisk-advance. es Teléfono nacional de servicio Comercial: 902 200 201 Teléfono nacional ce servicio Técnico: 902 300 301 Delegaciones, Distribuidores y Servicio Técnico a domicilio en todas las regiones de España FINLAND/SUOMI Oy Tecalemit AB Hankasuontie 13, 00390 Helsinki Tel. (89) 547 701- Fax (89) 547 1779 FRANCE Nilfisk-Advance S. A BP 246 91944 Courtaboeuf Cedex Tel. (01) 69. 59. 87. 00 Télécopie (01) 69. 59. 87. 01 PORTUGAL Nilfisk-Advance Lda. Rua Cândido de Figueiredo, 91-i, 1500-133 LISBOA Tel. [. . . ]