User manual NITECORE P25 SMILODON

[. . . ] Product testing data is in accordance with these internationally recognized scientific standards. Battery Installation Insert one 18650 battery or two CR123 batteries with the positive pole pointing forward (toward the light head). 1×18650 2×CR123 1h45min 30h 21h 325h 200h 1h15min 1h30min 5h15min 283m (Beam Distance) 20000cd (Peak Beam Intensity) 1. 5m (Impact Resistant) IPX-8, 2m (Waterproof AND Submersible) Dimensions Length: 160mm Head diameter: 40 mm Tube diameter: 25. 4mm Weight: 171g (without battery) Accessories Quality holster, clip, tactical ring, lanyard, USB cable, spare tail cap and spare O-ring Battery Options 18650 Rechargeable Li-ion battery Primary Lithium battery * Rechargeable Li-ion battery * SIZE Nominal voltage Compatible Yes (Compatible and can be recharged) Yes (Compatible but can NOT be recharged) Yes (Compatible but can NOT be recharged) 18650 CR123 RCR123 3. 7V 3V 3. 7V NOTE: Ensure batteries are inserted with the positive (+) end pointing to the head. The P25 will not operate with incorrectly inserted batteries. Switching ON/OFF *Warning: USB cable / charging function is for use with 18650 rechargeable li-ion batteries only. Do not attempt to charge non-rechargeable batteries such as CR123 or other types of rechargeable cells such as RCR123 batteries. To switch ON: Press the button on the tailcap until a “click” is heard. [. . . ] Do not attempt to charge non-rechargeable batteries such as CR123 or other types of rechargeable cells such as RCR123 batteries. Operating in Turbo Mode: With the light turned on, press the switch partway down and hold to activate turbo mode. Note: For user safety and to prevent overheating / failure, the P25 will automatically switch to high mode after twenty minutes of use in Turbo mode. Press the switch partway and hold to reactivate turbo mode when needed. Power Tips Standby Mode With the light turned on or in the standby mode, press the switch all the way down and release within one second to enter into standby mode. In this mode, the light will consume small amounts of power to maintain the settings in the MCU (micro control unit) but appear to be turned off. When in standby mode the power indicator light will flash once every two seconds to show the location of the light. To exit standby mode, simply press the two-stage switch all the way down or press the tail switch to turn the light off. Tips: When in standby mode，the P25 can also be used as a side-switch flashlight, all functions and brightness levels can be easily accessed via the 2-stage switch. 1. With the light switched on, the power indicator will blink once every two seconds when power levels reach 50%. With the light switched on, the power indicator will blink rapidly when power levels are low. Half press the switch when the light is put into standby mode or under charging mode, the power indicator light will blink in various patterns to indicate the battery voltage (accurate to ±0. 1V). For example, when the battery voltage is at a maximum charge of 4. 2V, the power indicator will blink 4 times in quick succession, followed by a one second pause and two more blinks, indicating a total battery voltage of 4. 2V. Changing / Charging Batteries Special Strobe / SOS mode and Location Beacon When the power indicator blinks rapidly it means the batteries need to be replaced or recharged. Alternatively if the light becomes dim or unresponsive to adjustment this also indicates batteries need to be replaced or recharged. With the light turned on, press the switch all the down and hold to enter strobe mode. When in strobe mode, press the switch partway down to cycle through SOS, location beacon and strobe modes. To select any of these modes simply release the switch when it is displayed. To turn off the light (enter into standby mode) fully press and release the switch. Maintenance Every 6 months, threads should be wiped with a clean cloth followed by a thin coating of silicon-based lubricant. Warranty Service Charging Function The P25 is capable of charging a protected 18650 li-ion battery via the included USB cable. Simply install a protected 18650 li-ion cell, plugging one end of the USB cable into the flashlight and the other end into a universal USB port / adaptor as shown in the adjacent image, and the P25 will take care of the rest. The P25 needs to be turned on in order enter charging mode. All NITECORE® products are warranted for quality. [. . . ] For the latest information on NITECORE® products and services, please contact your national NITECORE® distributor or send an email to service@nitecore. com Please follow our facebook for more info: NITECORE Flashlights Charging Indicator Light 1. Fully charging a depleted 18650 battery takes approximately 6 hours. Under normal charging conditions, the blue indicator light will blink once every 0. 5 second. [. . . ]