User manual NOKIA CONNECTIVITY TERMINAL 32 32 INSTALLATION GUIDE IN ENGLISH

[. . . ] 4 3. 2. 1 CALL MONITORING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3. 2. 1. 1 Busy tone monitoring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3. 2. 1. 2 Silence monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3. 2. 2 OTHER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NOKIA 32 INSTALLATION CHECKLIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4. 1 4. 2 4. 3 GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the multi-pair cable is used, the unused pairs should be grounded from one end. Connect only pins 1, 3 and 4 (trunk) and 3&4 in extension interface Use twisted pair cable to minimize disturbances. Tip: If the Nokia 32 terminal is connected to a PBX, and the B subscriber occasionally hears part of his/her own speech as an echo, tune the microphone sensitivity and/or voice volume. · · · · 2. 3 CONNECTING NOKIA 32 TERMINAL TO GSM NETWORK Check the field strength on the installation site. If the signal quality is poor, use an external antenna. Note: The terminal shows the signal strength immediately after it has registered to network (when Nokia 32 terminal is powered up). The field strength is shown with the terminal leds for ten seconds time. (see light indicator table for details). After the Nokia 32 terminal is turned on, check that the LED 3 lights up. If not, use the Nokia 32 configurator software and select the operator manually. Depending on the PBX interface where the Nokia 32 terminal is installed, check that the corresponding LED will turn on. (Led2 = Trunk mode, Led1 = Extension mode). Nokia 32 light indicators states during start-up LED 1 Green scan LED 2 Green scan Red blink Red blink LED 3 Green scan Red blink Description Power off Power on, connecting to network PIN query/ new PIN query PUK query Intensity of Field Strength Red blink Green blink Green Weak Unacceptable <- 105 dBm -105 . . . -100 dBm -100 . . . -95 dBm Green Green Green Green Green blink Green Green Green Green blink Green Good Moderate -95 . . . -90 dBm -90 . . . -85 dBm -85 . . . -80 dBm >-80 dBm Nokia 22 light indicators status during normal operation LED 1 * Green * * * * LED 2 Green * * * * * LED 3 Green Green Green blink Green blink Green/Red blink Red blink Description In service, trunk mode In service, extension mode Call on Incoming call Message received/ Voice mail in box Message storage full Nokia 32 light indicator status in special situations. LED 1 Green/Red blink Red blink Yellow LED 2 Green/Red blink Red blink Yellow LED 3 Green/Red blink Red blink Yellow Description Insert SIM card Failure, contact service Initialising 3. INTERFACES 3. 1 TRUNK INTERFACE An analog trunk interface of a PBX, or an analog telephone set can be installed to the trunk connector. The pin number 3 and 4 are TIP and RING. The right most pin of the connector is the ground connector (when the connector is looked from outside of the terminal). Connect pin 1 to the ground if the mains voltage might cause interference. 1, 2, 3, 4, 5, 6 1, 2, 3, 4, 5, 6 Note: Pin numbers equal to the physical connector, not the wire itself. After the installation check with a multimeter the resistance between the ground plate and ground connector of a building. Note: If you connect a landline phone to the trunk connector, check that only the pins 3 and 4 are connected from Nokia 32 terminal to the telephone set. 3. 1. 1 To be noted in trunk mode installation Tip: Check also the need of: · · Polarity reversal Loop interruption time · Ringing pattern Caution: Remember to define the appropriate emergency number in the General settings dialog. Caution: Remember to set the PIN query to ON, OFF or AutoPIN. 3. 2 EXTENSION INTERFACE Only an analog extension interface can be connected to the EXT connector. Only pins 3 and 4 are used as A and B. 1, 2, 3, 4, 5, 6 1, 2, 3, 4, 5, 6 Note: Pin numbers equal to the physical connector, not the wire itself. After the installation check with a multimeter the resistance between the ground plate and ground connector of a building. Note: The line impedance of Nokia 32 terminal is 600 and the maximum line current is 120mA There are some settings that should be programmed to a Nokia 32 terminal: 3. 2. 1 Call monitoring When informing of a disconnected call, a PBX uses either a busy tone, silence, or a combination of these. To end the call to the GSM network, the Nokia 32 terminal is able to monitor the busy tone or silence, but not a combination of these signals. You can change the call monitoring settings in the Nokia 32 Extension mode settings. [. . . ] Caution: In case of an incoming call, mode B is recommended. Otherwise the Asubscriber might be able to select a trunk line and set up a call e. g. Caution: Remember to set the PIN query ON, OFF or AutoPIN. 4. NOKIA 32 INSTALLATION CHECKLIST The purpose of this checklist is to be reminder of things to do or check when installing Nokia 32 terminal. 4. 1 GENERAL Ok Sim card is inserted is in the terminal properly. Nokia 32 will be registered to network when powered up (Led three is lit, Nokia 32 is in service) GSM field strength is strong enough Line adapter mode LED corresponds the installation (ext/trunk) Need of grounding. [. . . ]