User manual NORTHSTAR NS100 RADIO INSTALLATION SHEET

[. . . ] Radio Installation Sheet for NS100 VHF system Parts Checklist SINGLE SYSTEM (NS100SS) 1 x VHF Black Box Radio (single) DUAL SYSTEM (NS100DS) 1 x VHF Black Box Radio (dual) 1 x Hailer Cable ADDITIONAL WITH EACH SYSTEM 1 x Hand set with cord (US) PART CODE APNSBB2E8070 w w w . Nor th s tar Nav. c om Wiring Setup Antenna 10A Fuse 10A 1 x Mounting Template - Speaker 1 x Quickstart Guide and Reference Manual 1 x Quickstart Guide 1 x Radio Installation Sheet 1 x Warranty Sheet PPNSBB2E7030 PPNSBB2E7050 PART CODE APNSBB2E8080 PPNSBB2E7070 PPNSBB2E7260 PPNSBB2E7100 PPNSBB2E7110 MPLILTD-4/80 Power/NMEA HLR Station 1 Station 2 Ground lug APNSBB2E8030 3CH SCAN 16/9 COLOR RED BLACK GREEN YELLOW ORANGE BLACK FUNCTION PIN# BATTERY (+) 5 GROUND 1 NMEA IN (+) 2 NMEA IN (­) 6 NMEA OUT (+) 3 NMvEA OUT (­) 4 Power Cable Black Box Radio PWNSBB2E7120 1 x DSC Sticker 1 x Dust Cap for Handset connector plate OPTIONAL ADDITIONAL HANDSET KIT (NS100HS) 1 x Hand set with cord (US) PART CODE APNSBB2E8030 3CH SCAN 16/9 PART CODE Hailer Cable CALL WX FUNC HLR CALL WX FUNC 1 x Mic Plate - black 1 x Black Box to Speaker cord with Female-Female Adapter 3 x SS self tapping screws 1 x Mic Clip with magnet 2 x SS self tapping screws for mic clip 1 x Large Speaker MMNSBB2E4000 Female-Female adapter WALI08L07KX0 WALI08F08F0 COLOR YELLOW BLACK FUNCTION HAILER (+) HAILER (­) PIN# 1 8 1 x Mic Plate - black 1 x Black Box to Speaker cord with Female-Female Adapter 3 x SS self tapping screws 1 x Mic Clip with magnet MMNSBB2E4000 WALI08L07KX0 WALI08F08F0 Hand set & mike clip MS35-20SPSX1 APNSBB2E8050 MS35-20TSPX1 APNSBB2E8060 10 pin socket Hand set connector plate 3CH 16/9 MS35-20SPSX1 8 pin socket APNSBB2E8050 MS35-20SPSX1 APNSBB2E8060 Dust cap CALL SCAN WX FUNC 2 x SS self tapping screws for mic clip 1 x Large Speaker 1 x Speaker Gasket MPNSBB2E7040 Large speaker 1 x Speaker Gasket 4 x Speaker tabs 4 x SS self tapping screws 4 x SS self tapping screws 1 x Power Cable w/tags 1 x SS Grounding screw 1 x Spare 10A fuse 1 x Mounting Template - Black Box PPNSBB2E3270 MS35-20SPSX1 MS35-20SPSX1 WALI06LXXXX0 MS30-06PSNX2 PKFU125V10A0 PPNSBB2E7080 MPNSBB2E7040 4 x Speaker tabs 4 x SS self tapping screws 1 x Installation Sheet 1 x Dust Cap for Handset connector plate PPNSBB2E3270 MS35-20TSPX1 PPNSBB2E7030 MPLILTD-4/80 Tools Required · Drill ·1-1/4" Hole Saw 1/8" Drill bit Phillips Screwdriver · Sabre saw ·1" Hole Saw Pencil Installation Tips Installing Handset Connector 1. [. . . ] When removed, be sure to cover the connector with the provided dust cap. Installing Microphone Clip Plate 1. Mount the handset near the mounted connector allowing a drip loop in the MIKE cord. Be sure there is about 2" of vertical clearance to allow the handset to be easily lifted off and returned to the clip plate. Place the clip plate on the dash with the magnetic sensor toward the rear. Using the clip plate as a guide, mark the 2 holes. Mount the clip plate with the 2 screws provided. Mount the handset connector. Speaker is at least 45cms (1. 5') from the compass 2. 4. 5. Black Box Radio must be at least 1metre (3') from the Antenna 6. 7. Wiring Hailer Connector Location Requirements - Please check these before doing any cutting or drilling. Ensure that the chosen location: · is at least one metre (3') from the antenna · allows easy connection to (at least) a 10 Amp fused 12V only DC electrical source and the antenna. · is at least 45cms (1. 5') from the compass to avoid creating magnetic deviation of the compass during radio operation · has a suitable space close by for installing the microphone bulkhead mount · provides easy access to the front panel controls · provides reasonable access to the wiring at the back of the radio. Check that the location of the powerful 20W 4 Ohm HAILER HORN (not provided) does not effect the ship's compass before drilling holes and mounting. [. . . ] Mount the speaker with supplied gasket from the front and hook up the connectors. . Put the 4 speaker clips on the speaker to cover up the mounting holes for a professional look. 2. 6. CAUTION NOTE: DO NOT GROUND EITHER SIDE OF THE HAILER WIRES. PPNSBB2E7080 ( L A0 0 040 6A) [. . . ]