User manual NOVA CONTROLS PRO-FLOW

[. . . ] Pro-Flow Drain Cleaning DISPENSER AND REMOTE PROGRAMMER Reference Manual Installation and Programming Quick Start Guide on Back Cover - Kurzanleitung auf Deckelrückseite - Guide Rapide de Début sur la Couverture Arrière - Guía Rápida de Programación en la Contratapa - Guida Rapida di Inizio é sulla Copertura Posteriore - Guia Rápido de Programação na Contracapa Copyright 2006 Nova Controls, Inc. D Specifications Note Specifications subject to change without notice. Pro-Flow Dispenser Size Weight Total Amperage draw during operation Pump Flow Rate Temperature Humidity Indoor Installation Altitude 5. 18" W x 3. 5" H x 1. 9" D (13. 2 cm W x 8. 9 cm H x 4. 8 cm D) 5. 6 oz. (159 g) 400 mA 6 oz / minute (180 ml / minute) 20° to 150° F (6° to 65° C) maximum 95% relative humidity maximum Approved for indoor use only. (2000m) maximum Battery Pack Size Weight Battery Approximate Battery Life 5. 71" W x 5. 33" H x 1. 55" D (14. 50 cm W x 13. 54 cm H x 3. 94 cm D) 8 oz. [. . . ] After setting the current day and time on the remote, the installer need only press the SEND button to load the pre-set formula, date and time into the dispenser. (300 ml. ) of product, dispensed at midnight, seven days per week. Each product dose is called an event (event = day + time + dosage). The pre-set formula has seven events (Sunday - Saturday). If desired, the installer can edit the pre-set formula to create new formulas. Up to three formulas (including the factory pre-set) can be saved in the remote. The remote's back-up lithium battery saves clock and formula settings, even when the remote is off or the 9-volt battery is being replaced. Basic Operation of Remote Programmer Turn On: Press the POWER button . The Home Screen (current day and time) displays. (If the battery is low, BAT LOW displays first, then the Home Screen. ) Start from the Home Screen to program a dispenser. Turn Off: Press and hold the POWER button minutes of inactivity. Remote turns off automatically after 2 First-Time New Remote Set-up Before using a new remote, you must: 1. Insert the 9-volt battery (included) and secure the battery cover. Set unit of measurement while you power on the remote. If ML is preferred, skip to Step 2 before turning on the remote: 1. If OZ is preferred , press the POWER button and turn on the remote. If ML is preferred , press and hold the ENTER button , while also pressing Power . This turns on the remote and changes to metric. ML displays briefly, followed by the Home Screen. Set the 24-hour clock with the local day and time in military format, 00:00 - 23:59. (See "Set the Clock" on page 10 for instructions. ) · Underscored item can be revised. · Right /Left arrows move the underscore. · Up / Down arrows set the value of the item. Figure 3-1 Remote's Clock Screen Display HRS P/N 20-08363-00 Rev. [. . . ] Pressing CHECK will display the dispenser's new formula to verify that the correct formula was received. Caution If you are within range of a dispenser and press CHECK, you will LOSE the program currently on the screen. It will be replaced by the dispenser's program. Troubleshooting If COM BAD displays instead of SET, the formula was NOT successfully downloaded. The most likely reasons are: the remote is too far from the dispenser; the remote is angled more than 7° to the right or left of the dispenser, there is an obstruction between the remote and the dispenser; the remote is not pointed directly at the dispenser, and/or the dispenser is in bright light or sunlight. If the remote's factory pre-set formula is accidentally lost, quick recovery is possible by aiming the remote at a brand new dispenser (that is powered on) and pressing CHECK. [. . . ]