User manual NOVAK GOAT PROFILE SELECTION & GEARING GUIDE
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual NOVAK GOAT PROFILE. We hope that this NOVAK GOAT PROFILE user guide will be useful to you.
Lastmanuals help download the user guide NOVAK GOAT PROFILE.
Manual abstract: user guide NOVAK GOAT PROFILESELECTION & GEARING GUIDE
Detailed instructions for use are in the User's Guide.
[. . . ] DRIVE FREQUENCY-Brush-Mode Only-(1of7settingsfrom3. 5to15kHz)--The frequency at which the duty cycle information is being sent from the speed control to the motor to control the speed. Raising this setting makes the control of the motor feel more smooth. Normally this value would be lowered for use with higher turn motors to get more `punch', and it would be raised for hotter, low-turn motors or slippery track conditions for more control of the power delivery.
allLEDs
WithESCon&connectedtoachargedbattery(transmitterONorOFF): 1. IF TRANSMITTER IS OFF, DISCONNECT ESC FROM RECEIVER 2. [. . . ] In Brushless Profiles 1 & 2, the brakes linearly ramp up to the value of Drag/Hill brakes that you program. This provides smooth application of braking without risk of roll-overs.
mOtOr rOtAtiON SeleCtiOn
The Goat's software lets you reverse the brushless motor's rotation direction. This allows installation in vehicles with counter-rotating drive trains (oropposedtransmissions), without compromising performance. See reverse side of this sheet for programming instructions
P5
advanced -- CUSTOM programmiNG
to custom program profiles:
YourtransmittercanbeeitherONorOFF:
1. IF TRANSMITTER IS OFF, DISCONNECT ESC FROM RECEIVER
Remove input signal harness from receiver to avoid radio interference.
to activate & adjust drag brake:
a. PRESS & HOLD SPEED CONTROL'S SET BUTTON b. SELECT DRAG BRAKE PERCENTAGE
Drag Brake Values for Brushless Profiles: With ESC at neutral, press & hold SET button until the BLUE & AMBER status LEDs turn on solid---Release SET button once LEDs are on solid. blue&amberLEDs Blue & Amber status LEDs flash to indicate the Drag Brake setting. Quick press & release the SET button to change the Drag Brake setting.
2. CONNECT SPEED CONTROL TO A CHARGED BATTERY PACK 3. SLIDE ESC's ON/OFF SWITCH TO `ON' POSITION 4. MAKE SURE THE THROTTLE PROFILE TO ADJUST IS ACTIVE
If you are not sure what profile is selected, follow the procedures in `Throttle Profile Selection' to check or select the desired profile. You can adjust different parameters(describedonbacksideofthissheet)to fine tune the speed control to perform & feel the way you like it. Remember that you can not access the Brush-Mode (Profile #4) without disconnecting the brushless motor's sensor harness from the ESC. Note: there is no time constraint during selection process of custom parameters.
5. FOLLOW STEPS ON RIGHT SIDE OF THIS PAGE TO CUSTOMIZE ESC
Setting(#offlashes):
BLUE & AMBER LEDs ON ALWAYS
Drag/HillBrake(%): 1. 5
Drag Brake Values for Brush-Mode:
1
2
3
4. 5
3
7. 5
4
9. 5
5
10. 5
6
12
7
13. 5
8
Setting(#offlashes):
BLUE LED STAYS ON ALWAYS
Drag/HillBrake(%): 10
1
20
2
25 30
3
4
40
5
50
6
60 70
7
8
80
9
10
90
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
goat soFtware Flow chart: @NEUTRAL
REDLED on solid press&hold
Selection is stored in memory--StatusLEDsscrollback&forthandESCexitsprogramming. Red LEDturnsonsolid(Blue&AmberLEDswillalsobeon)---ESCisatneutral&readytogo.
to adjust dead band:
a. PRESS & HOLD SPEED CONTROL'S SET BUTTON b. SELECT DEAD BAND PERCENTAGE
With ESC at neutral, press & hold SET button until the BLUE & GREEN status LEDs turn on solid--Release SET button once LEDs are on solid. blue&greenLEDs Blue & Green status LEDs flash to indicate active Dead Band setting. Quick press & release SET button to change setting.
DRAG BRAKE
ifProfile#3active BLUE&AMBER press&hold continueholdingESC'sSETbuttontoskipstepshere
Setting(#offlashes):
DeadBand(%):
1
3
2
5
3
6
4
7
5
9
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
DEAD BAND
BLUE&GREEN press&hold
Selection is stored in memory--StatusLEDsscrollback&forthandESCexitsprogramming. Red LEDturnsonsolid(Blue&AmberLEDsmayalsobeon)---ESCisatneutral&readytogo.
to adjust minimum drive:
a. [. . . ] amber&redLEDs Amber & Red status LEDs flash to indicate LiPo Cut-Off Circuitry setting. Quick press & release SET button to change setting. 1 flash = OFF 2 flashes = ON Selection is stored in memory--StatusLEDsscrollback&forthandESCexitsprogramming. Red LEDturnsonsolid(Blue&AmberLEDsmayalsobeon)--ESCisatneutral&readytogo.
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
to reverse motor rotation:
a. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE NOVAK GOAT PROFILE
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual NOVAK GOAT PROFILE will begin.
