User manual NOVAK GOAT 3S BASIC SETUP GUIDE

[. . . ] transmitter adjustments ·NOT ALL TRANSMITTERS HAVE THESE ADJUSTMENTS· trouble-shooting guide steering channel works but motor will not Run ·Red & Green status LEDs on solid­­Check input signal harness connections at ESC and receiver. Check input signal harness wiring sequence­­Refer to Step 1. ·Red status LED on solid & Green LED blinking­­Check motor sensor harness connection. ·Blue & Green status LEDs both blinking. [. . . ] Fill out the needed information on this form and return it with the Novak product that requires servicing. PHONE/FAX: If you do not have access to the internet, please contact our customer service department by phone or fax. PRODUCT SERVICE FORM & include a valid cash register receipt with purchase date and dealer name & phone # on it, or an invoice from previous service. If warranty provisions have been voided, there will be service charges. NOVAK bRuSHLESS MOTORS ONLy bRUshlEss EXtEnsIon haRnEssEs [Novak kits #S5357 & #S5358] Optional harnesses are available in two lengths (4" in Novak kit #S5357 & 9" in Novak kit #S5358). NO REVERSE VOLTAGE! pOWER TRANS-CAp MODuLE REQuIRED TRANSMITTER ON FIRST product warranty The Goat 3S Brushless/Brush ESC is guaranteed to be free from defects in materials or workmanship for a period of 120 days from the original date of purchase (verified by dated, itemized sales receipt). This product is not intended for use by children under 14 years of age without the strict supervision of an adult. Use of this product in an uncontrolled manner may result in physical damage or injuries--take extra care when operating any remote control vehicle. in Irvine, CA and assembled with globally sourced components. · All Rights Reserved · No part of these instructions may be reproduced without the written permission of Novak Electronics, Inc. · Goat 3S ESC, Smart Braking II, Polar Drive Technology, Radio Priority Circuitry & One-Touch Set-Up are all trademarks of Novak Electronics, Inc. WEB SITE: Print a copy of the PRODUCT SERVICE FORM from the CUSTOMER SERVICE GOOD QuALITy Li-po bATTERIES SuGGESTED WARRANTy SERVICE: For warranty work, you MUST CLAIM WARRANTY on GOOD QuALITy RADIO SySTEM SuGGESTED NOVAK ELECTRONICS, INC. P: (949) 833-8873 · F: (949) 833-1631 customer service E-mail: cs@teamnovak. com www. teamnovak. com P4 · ESCs returned without a serial number will not be serviced under warranty · ADDITIONAL NOTES: ·Dealers/distributors are not authorized to replace products thought to be defective. ·Ifahobbydealerreturnsyourproductforservice, submitacompletedPRODUCT SERVICE FORM to the dealer and make sure it is included with product. ·NovakElectronics, Inc. doesnotmakeanyinternalelectroniccomponents(transistors, resistors, etc. ) available for sale. DO NOT buNDLE pOWER & SIGNAL WIRES TOGETHER RF noise in the power wires can adversely effect radio system performance. Always insulate exposed wiring with heat shrink tubing or electrical tape to prevent short circuits. Exposure to CA glue or its fumes can cause damage to internal components of the ESC and result in premature failure. INSuLATE WIRES NO CA GLuE P1 step 1­connect The Goat 3S has a user-replaceable input harness with the industry-standard receiver connector on it & works with all major radio brand's new receivers (Refer to Figure 1 to see how to connect the included user-replaceable input harness to Novak's XXtra Synthesized FM Receiver: 75 Mhz). However, some very old receivers must have the wiring sequence in the plastic 3-pin JST connector housing changed on the receiver end. This is important, as the receiver & servo electronics may be damaged if the sequence is incorrect. For instructions on changing the wiring sequence for older receivers, visit the Novak Web site. input harness step 3­wirinG speed control to motor bRuSH-typE mOtOrS (Fig. dIsconnEct bRUshlEss motoR sEnsoR haRnEss 2. motoR capacItoRs The Goat 3S ESC automatically switches to Brush-Mode when the ESC's power is switched ON and no brushless motor sensor harness is connected. Electric brush-type motors generate RF noise that causes interference. Novak's 0. 1µF (50V) non-polarized, ceramic capacitors (Novak #5620) must be used on all brushed motors to reduce motor noise & prevent ESC damage. Note: Some motors come with built-in capacitors. If your motor only has 2 capacitors, you need to install a capacitor between the positive & negative motor tabs­­If you experience radio interference with built-in capacitors only, install external ones. step 4­wiring esc to battery (Fig. [. . . ] NOTE: Whenever the One-Touch set-up is performed, the ESC will automatically revert back to the factory default settings, & the Throttle Profile will revert to #2 when in Brushless-Mode. DO NOT uSE SCHOTTKy DIODES 3. sEcURE powER tRans-cap modUlE to chassIs DO NOT uSE SCHOTTKy DIODES MOTOR CApACITORS NOT NEEDED 4. Install on/oFF swItch Use a screw or the included double-sided tape, and mount the switch where it will be easy to access--be sure to select a position where it will not get damaged or get switched OFF during a crash or roll-over. ESC ON/OFF Switch (Turn on 2nd) bRuSH-MODE SET-up pHOTO (Fig. [. . . ]