User manual NOVAK HAVOC SPORT ESC CUSTOM PROGRAMMING AND GEARING GUIDE

[. . . ] Stock radio equipment and sport "stick-type" battery packs should work safely. These gearing recommendations are intended to provide initial safe operation. BrUsHLEss MOTOrs Havoc 8. 5 SS8. 5 Pro (Novak #3408) SS10. 5 Pro (Novak #3410) SS13. 5 Pro (Novak #3413) SS17. 5 Pro (Novak #3417) SS21. 5 Pro (Novak #3421) Motor output linear Novak's Throttle Curve adjustment allows drivers to tailor the throttle response of a vehicle, creating either a quick burst of power with the Linear Curve setting, or a smoother, controlled low-end power delivery with the Expo Curve setting. expo 0 Trigger position 100% Setting is fixed at "Linear" in Brush Mode. The Throttle Curve is selectable in Brushless Mode. PINION GEAr rANGE 15 through 20-tooth 15 through 20-tooth 17 through 22-tooth 20 through 27-tooth 25 through 30-tooth 28 through 33-tooth L I - P O C U T- O F F C I R C U I T R Y When active (see programming on reverse side to turn ON/OFF), the built-in Smart-Stop Li-Po Cut-Off Circuitry lets you safely use Lithium Polymer batteries by cutting off the ESC's throttle output when a critical safety voltage is reached. Decrease the pinion tooth number by 2-3 for motors without sintered rotors. ESC's factory default is Li-Po Cut-Off Circuitry Active The circuitry constantly monitors the pack voltage. [. . . ] The 23-tooth pinion gear included in the RTR kit will provide speeds above 40 mph with a 7-cell battery pack. * THROTTLE PROFILES NOTE: The havoc's software has an Auto-Detect Brush-Mode. This feature will automatically switch the eSC from the Brushless Throttle Profile to Brush-Mode when it does not have a brushless motor's sensor harness plugged into it at start-up. BrUsHLEss PrOFILE BrUsH-MODE M O T O R R O TAT I O N S E L E C T I O N The Havoc software lets you reverse a brushless motor's rotation direction (see reverse side of this sheet to select rotation). This allows installation in vehicles with counter-rotating drive trains (or opposed transmissions), without compromising performance. Because the ESC will be operating in its normal forward & reverse modes, features like Smart Braking continue to operate normally. 1 w/Reverse Reverse% Programmable Minimum Brake% Drag Brake Dead Band% Minimum Drive% Throttle Curve Brake Frequency Motor rotation Li-Po Cut-Off on 100% yes 0% off 6% 1% expo on on on 2 on 100% yes 0% off 6% 1% linear off off on The Havoc ESC reverts back to default settings when One-Touch set-up is performed. The Havoc ESC is fully programmable, refer to page 6 for fine-tuning options. www. teamnovak. com *At the time of printing, the Traxxas® SlashTM RTR kit included an 18-tooth and a 23-tooth pinion gear. SlashTM is a registered trademark of Traxxas®. P5 H AV O C s p O R t E s C C u s t O m p R O G R A m m I N G pleASe noTe: This page contains optional Advanced Programming items!No further adjustments are required. (But don't worry, you can always reset factory defaults by performing the One-Touch programming again, so go ahead & experiment--that's why the programming is in there, right?) HAvOC SPORT ESC SOFTWARE FLOW CHART The Havoc Sport ESC features nine parameters that can be adjusted. iF TrAnSMiTTer iS oFF, DiSConneCT eSC FroM reCeiver Remove input signal harness from the receiver to avoid radio interference. ConneCT eSC To A ChArGeD BATTerY pACK 3. SliDe eSC's on/oFF SwiTCh To `on' poSiTion 4. wiTh eSC AT neuTrAl preSS & holD eSC'S SeT BuTTon release EsC's sET button once LED is at desired setting. To skip a parameter, press and hold ESC's SET button to the desired parameter. SeleCT pArAMeTer vAlue LED flashes to indicate active setting (refer to tables at right). Quick press & release SET button to select desired setting. preSS & holD SeT BuTTon To STore SeleCTion When SET button is pressed and held for about 1 second, the new selection is stored in ESC's memory--The 4 status LEDs will scroll across to indicate ESC is exiting programming and ESC returns to neutral. note: There is no time constraint during selection process of custom parameters. THROTTLE PARAMETER SETTINGS (Defaults in Bold) 1. [. . . ] Note: Setting is fixed at "Linear" in Brush Mode. ThroTTle Curve* GREEN setting (# of flashes) Throttle Curve: 1 Linear 2 expo rED LED press & hold BrAKe FreQuenCY* RED 6. BraKe freQueNcY* (7) press & hold RED / GREEN / AMBER >>raising this setting makes the brake response smoother and more controllable. reverSe* press & hold setting (# of flashes) Brake Frequency (KHz): 1 1 2 2 3 3 4 4 5 5 6 7. 5 7 8 7. reVerse* (2) setting (# of flashes) reverse (On/Off): RED, GREEN & AMBER LEDs 1 Off (FWD/BRK) 2 on (FwD/BrK/rev) MoTor roTATion* RED / GREEN / BLUE >>Changing this setting activates/deactivates reverse direction. press & hold li-po CuT-oFF RED & AMBER 8. [. . . ]