User manual NOVAK HV PRO

[. . . ] step 5­one-touch programming using a receiver battery pack If using an external receiver battery pack with the HV Pro ESC: 1. Plug an external 5 cell (1. 2VDC/cell) receiver battery pack into the battery slot of the receiver. Leave the HV Pro's ON/OFF switch in the OFF position, and use receiver battery pack's ON/OFF switch to turn the system power on and off­­DonotusetheESC'sswitch. 12VDC BATTERY NOTE: An external receiver battery pack must be used when using the HV Pro with a single 12 volt battery, like a lead acid or gel cell. will not provide enough output due to the high voltage directed through the single battery input, resulting in degraded servo/receiver performance and B. E. C. [. . . ] 5841 Double-Sided Mounting Tape--100pcs--1"x1" high-performance clear mounting tape. 5912 HV Sintered Rotor--1/8"--Sintered neodymium rotor for 1/8" shaft HV-series motors. 5914 HV Sintered Rotor--5mm--Sintered neodymium rotor for 5mm shaft HV-series motors. 5917 Ribbed End Bell & Bearings--5mm--Front end bell & bearings for 5mm shaft HV motors. 5919 Ribbed End Bell & Bearings--1/8"--Front end bell & bearings for 1/8" shaft HV motors. 5931 550-Size Motor Hardware Kit--Replacement shims & screws for 550-size Novak motors. PRECAuTIONS Never expose ESC to water, moisture, or other foreign materials. Disconnect battery packs from ESC when not in use to avoid short circuits & possible fire hazard. NiMH--NEVER use fewer than 6 or more than 14 cells (1. 2V/cell) & be sure LiPo Cut-Off is turned OFF. LiPo--Use dual 2-cell (2S) packs for main battery & be sure the LiPo Cut-Off option is turned ON. The HV Pro ESC is specially designed for use with sensor-based Novak HV-Series 550-size Brushless Motors Only!Novak 540-size motors should not be used. Free-running your brushless motor in a no-load condition can result in rotor failure and speed control transistor damage & will void the product's warranty!Reverse battery polarity can damage ESC & void warranty. ESC heat sinks MUST be used (and included fan should be used) for optimum cooling. Allowing individual heat sinks to touch each other or any conductive surface will short circuit & damage ESC. The HV Pro's factory-installed external Power Trans-Cap Module MUST be used. Failure to use PowerCap Module will result in higher ESC temperatures & thermal shut-down. Always turn on transmitter power first so you will have control of the vehicle when you turn it on. With the higher performance of brushless systems, undesirable radio system noise may occur when used with lower quality transmitters (like some RTR radios). WATER & ELECTRONICS DON'T MIX! DISCONNECT BATTERIES WHEN NOT IN USE 6 TO 14 CELLS OR 2-4 CELL LiPo ONLY NOVAK MOTORS ONLY B. Set LOW ATV, EPA, or ATL to maximum setting. Fill out the needed information on this form and return it with the Novak product that requires servicing. PHONE/FAX: If you do not have access to the internet, please contact our customer service deptartment by phone or fax. . [. . . ] Test fit motor in vehicle to align pinion and spur gears, then tighten pinion gear on shaft. using a single battery pack: 5. CHECK MOTOR SCREW LENGTH FIGURE 3 With a small standard screwdriver, gently lift plastic prong until wire and metal socket easily slide out of plastic housing. You must check the length of the motor screw to ensure that the motor will not be damaged. You should have no more than 1/8" of screw extending past the vehicle's motor mounting plate (2-4mm). Too little can strip the threads in the end bell, and any more will cause damage & short-circuiting inside the motor & will void warranty. [. . . ]