User manual NOVY 7901

[. . . ] 2 CUT-OUT IN THE TABLE TOP FOR FLUSH MOUNTING Cut-out in the table top: X = 502 mm (tolerance -0/+1) Y = the overall dimensions of the domino + the distance in between must every time be 2 mm + UP_SIDE(s) - 10 mm EN 20 Milled groove: X = 526 mm Y = the total width of all appliances + space for the silicon (3 mm between the table top and the appliance, 2 mm between 2 appliances) Z = the depth of the milled groove = the thickness of the glass of the cooking plate + 1, 5 mm (tolerance -0/+0, 5 mm) Example with 2 x UP_SIDE and 3 domino elements: Domino 2 zone (380 mm) + UP_SIDE (110 mm) + Domino 2-zone (380 mm) + UP_SIDE (110 mm) + Domino wok (380 mm) Flush mounting: Opening X = 502 mm Y = (380 mm + 2 mm + 110 mm + 2 mm + 380 mm + 2 mm + 110 mm + 2 mm + 380 mm) - 10 mm Milled groove X = 526 mm Y = 3 mm + 380 mm + 2 mm + 110 mm + 2 mm + 380 mm + 2 mm + 110 mm + 2 mm + 380 mm + 3 mm 1. €¢ A: Remove the 8 screws of the sound-insulating outlet . €¢ B: Turn the electronics box by removing the 4 screws and by placing back the box upside down (cables facing up). €¢ C: Turn the outlet 180° again with the 8 screws. [. . . ] For additional information see chapter 5. €¢ Make use of the connecting piece when connecting the flat duct to the outlet of the UP_SIDE. General: • Make the duct as short as possible and with as few as possible bends to the outside. Use rounded bends for proper air conduction. €¢ If an exhaust pipe through the outside wall passes a cavity wall, make sure that the exhaust duct fully bridges the cavity and slightly declines to the outside. €¢ In case of an exhaust pipe through the roof, use a double-walled roof passage with sufficient width. Fresh air can be supplied by slightly opening a window or an outside door or by installing an inlet grate. €¢ Use the delivered white insulating tape for an airtight seal (801-006). 4 APPLIANCE ADJACENT TO THE UP_SIDE For surface mounting and flush mounting • On the appliance that is not placed above the motor casing of UP_SIDE the delivered black PVC strip (7900-094) must be applied at the front and the rear. This is to set off the difference in height. €¢ Stick the strip at the front and at the rear. For surface mounting: • Place the domino and/or induction hotplate besiUP_SIDE. For flush mounting: • Place the appliance(s) besiUP_SIDE. The drip tray is just not touching the decorative frame of the UP_SIDE. EN 23 3 ADJUST THE SUCTION UNIT OF UP_SIDE By default the click system is properly adjusted such, that the suction unit (990984) locks into place in the suction opening. Adjust the click system (only in the following cases): Suction unit (C) does not stay down = distance between A and B too large Suction unit (C) cannot be fully pushed down = distance between A and B too small If adjustment is still required, follow this instruction. Adjust the click system (A) and the hook (B): • Remove the suction unit (C) from the hood and remove the lid (D) from the box. €¢ Slightly unscrew the 4 capped nuts, so you can slide the foot (E) together with the click system (A) into the longitudinal direction. €¢ Place the suction unit (C) back and push it fully downwards. €¢ Press the foot (E) together with the click system (A) until it is against the hook (B). €¢ Tighten the capped nuts (manually). • Place back the lid (D). [. . . ] In case of a cabinet with a limited depth, this adapter is the ultimate solution to allow installation with flat ducts. The adapter is mounted unto the outlet of UP_ SIDE to which a flat duct can be connected directly. More information for connecting the adapter can be found in the mounting instructions for the adapter. Recirculation UP_SIDE can be connected to an exhaust box with a monoblock recirculation filter. [. . . ]