User manual NVIDIA GA-K8N-SLI

[. . . ] GA-K8N Ultra-SLI / GA-K8N Pro-SLI / GA-K8N-SLI AMD Socket 939 Processor Motherboard User's Manual Rev. 1004 12ME-K8NUSLI-1004 Motherboard GA-K8N Ultra-SLI Motherboard GA-K8N Ultra-SLI Jan. 12, 2005 Motherboard GA-K8N Pro-SLI Motherboard GA-K8N Pro-SLI Feb. 25, 2005 Motherboard GA-K8N-SLI Motherboard GA-K8N-SLI Aug. [. . . ] The parameter can be adjusted from 0~127. Higher parameter means faster CPU fan speed. (Default parameter: 80) The CPU fan runs at full speed when both CPU Smart FAN Control and CPU FAN Manual Control are disabled. (Note) Whether the CPU Smart FAN Control function is supported will depend on the CPU you install. For more detailed information please check at the FAQ section on GIGABYTE's website. - 47 BIOS Setup English Temp of FAN turn off (Default temperature: 0oC) When the CPU temperature is below the value set in this option, the CPU fan will stop spinning. Temp Limit of Low Speed (Default temperature: 20oC) The CPU fan will stop spinning when the CPU temperature is below the value set in Temp of FAN turn off option. The CPU fan will start to spin again with the parameter set in CPU FAN: Low Speed when the CPU temperature exceeds the value set in Temp Limit of Low Speed. Temp Limit of Mid Speed (Default temperature: 50oC) When the CPU temperature exceeds the value set in this option, the CPU fan spins with the parameter specified in CPU FAN: Mid Speed. For example, by default, when the CPU temperature exceeds 50 o C, CPU fan runs with parameter 12. Temp Limit of High Speed (Default temperature: 60oC) When the CPU temperature exceeds the value set in this option, the CPU fan rotates with the parameter specified in CPU FAN: High Speed. For example, by default, when the CPU temperature exceeds 60 o C, CPU fan runs with parameter 80. Temp of full FAN Speed (Default temperature: 70oC) When the CPU temperature exceeds the value set in this option, the CPU fan runs at full speed. K8 nForce4 SLI Series Motherboard - 48 - 2-7 MB Intelligent Tweaker(M. I. T. ) CMOS Setup Utility-Copyright (C) 1984-2005 Award Software MB Intelligent Tweaker(M. I. T. ) HT Frequency ratio CPU Frequency K8 CPU Clock Ratio Current DDR speed DDR Clock/ Timing Mode CPU/DDR clock Ratio DDR Speed DDR Timing CAS# latency (Tcl) Min RAS# active time (Tras) RAS# to CAS# delay (Trcd) Row precharge Time (Trp) Row to Row delay (Trrd) Row cycle time (Trc) Row refresh cyc time (Trfc) Read-to-Write time (Trwt) Write Recovery Time (Twr) Wirite-to-Read Delay (Twtr) Refresh Rate (Tref) : Move [Auto] [200] [Auto] 266 [Auto] 2/1. 33 266 Auto 2. 5 6T 3T 3T 2T 9T 10T 4T 2 bus clock 1 bus clock 133MHz, 15. 6 us Item Help Menu Level English x x x x x x x x x x x x Enter: Select +/-/PU/PD: Value F5: Previous Values F10: Save ESC: Exit F7: Optimized Defaults F1: General Help CMOS Setup Utility-Copyright (C) 1984-2005 Award Software MB Intelligent Tweaker(M. I. T. ) x Read Preamble value x Async Latency value CPU Spread Spectrum PCIE Clock Robust Graphics Booster CPU Voltage Control Normal CPU Vcore Chipset core PCI-E voltage HT-Link voltage control DDR voltage control 7ns 7ns [Center Spread] [100Mhz] [Auto] [Normal] 1. 500V [Normal] [Normal] [Normal] Item Help Menu Level : Move Enter: Select +/-/PU/PD: Value F5: Previous Values F10: Save ESC: Exit F7: Optimized Defaults F1: General Help Incorrect using these features may cause your system broken. For power end-user use only. HT Frequency ratio Set HT Frequency ratio to 1x, 1. 5x, 2x, 2. 5x, 3x, 4x, or 5x. (Default: Auto) CPU Frequency 200 ~ 456 Set CPU frequency from 200Mhz to 456Mhz. K8 CPU Clock Ratio This setup option will automatically assign by CPU detection. The option will display "Locked" and read only or will not show up if the CPU ratio is not changeable. - 49 BIOS Setup English Current DDR Speed Displays the current DDR speed. DDR clock/Timing Mode Auto Manual Set DDR Clock and Timing Mode automatically. (Default value) Set DDR Clock and Timing Mode manually. CPU/DDR clock Ratio Set the CPU/DDR clock ratio. Options include 2/1, 2/1. 33, 2/1. 5, 2/1. 66, 2/1. 83, 2/2. DDR Speed This item changes according to the value set in CPU/DDR clock Ratio. DDR Timing Auto Manual BIOS will automatically set up the DDR Timing by DRAM SPD data. (Default value) This item allows user to set DDR Timing manually. Set CAS Latency to1. 5/2/2. 5/3 (Default value:2. 5) BIOS will automatically detect the minimum RAS Active Time. Set the minimum RAS Active Time to 5T~15T (Default value:6T) Set DRAM RAS to CAS Delay to 2T/3T/4T/5T/6T/7T. (Default value:3T) BIOS will automatically detect the Row Precharge Time. Set the Row Precharge Time to 2T/3T/4T/5T/6T/7T. (Default value:3T) BIOS will automatically detect the Row to Row delay. (Default value:2T) Set Row Cycle Time to 7T~22T. [. . . ] Support : http://tw. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address : http://www. gigabyte. de Japan NIPPON GIGA-BYTE CORPORATION WEB address : http://www. gigabyte. co. jp Singapore GIGA-BYTE SINGAPORE PTE. Support : http://tw. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address: http://www. gigabyte. com. sg U. K. [. . . ]